×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerStructural elements. This means the structural behavior can be quantified by considering the behavior of each structural element in each load path. Concrete is a material known for its great strength. Regardless, there are a few weaknesses, which must be taken in consideration in the design of concrete structural elements. Basically, concrete is made of three main ingredients: Portland cement, water, and aggregates (sand and stone).In order to improve tensile strength and ductility (capacity to stretch and deform prior to failure) in concrete, so this paper discus some types of concrete and record the effect on beams. Reactive powder concrete (RPC) is an actual concrete mixture, it is a special type of concrete because mix concrete (coarse and fine aggregate ) replaced by fine sand size (150-400)µm. In the experimental comparison the mechanical properties( compressive , splitting tensile and flexural )strength of plain RPC and high and normal strength concrete. Each set consisted of (4) cubes of (100×100×100_mm, (8) cylinder of (150×300mm) and (4) prism of (100x100x500) mm and consisted of (4) beam of (1000×100×400)mm. The results shown that the maximum compressive strength is 107 MPa and the maximum splitting tensile 9 MPa of RPC comparison high and normal strength concrete. The result of the second part shown increased RPC reinforced concrete the firstcrack288 MPa and ultimate crack 380MPa comparison high and normal strength concrete and the mode of failure of RPC (flexural-shear).
Construction joints are separations between successive concrete pours. They are critical in the building of large concrete structures, since these structures cannot be cast in a single pour. Self-consolidation concrete is a relatively new kind of concrete that is considered suitable for a wide range of construction applications, especially those needing a high early resistance. Certain findings from earlier experimental tests were adopted and analyzed using finite element analysis. ANSYS program was used to analyze the impact of utilizing high strength concrete (fc') and the secondary reinforcement ratio (ρv) on the behavior of reinforced self-consolidating concrete beams having a horizontal construction joint. Nine beams analyzed in this study have the same dimensions (150×180×1200) mm (width× height ×length). Between the two supports, the clear span was 1100 mm. Two-point loads were applied to the simply supported beams during testing. One of the beams acts as a control beam (without a construction joint) and the remaining beams were with horizontal construction joint in the tension zone. The ultimate loads obtained analytically vary by between 3.1% and 7.8 % from those found experimentally. The presence of the horizontal construction joints made the beam less stiff. Utilizing a 70 MPa high strength concrete resulted in a 47.4 % in ultimate load over the experimental value for regular strength concrete (28 MPa). Increasing the ratio of secondary reinforcement (0.01229 to 0.049) resulted in a 10.3% increase in ultimate load magnitude, while decreasing the ratio of secondary reinforcement (0.01229 to 0.0025) with spanning the spacing between stirrups led to a reduction in ultimate load magnitude by 55.8%.
Concrete is considered the most important and widely used building material in the world of construction and building due to its durability, high efficiency in shaping, and relatively reasonable cost. The main component of concrete is cement, and one of the most important problems related to cement is the environmental problems associated with cement manufacturing, as the cement manufacturing process releases a large amount of carbon dioxide. Despite the essential role of concrete in construction, we cannot ignore its environmental impact. Some claim that exploring alternative materials or innovative building techniques would reduce the carbon footprint and enhance sustainability in the industry. Partial cement replacement with pozzolanic materials like zeolite is a key technique to reduce carbon dioxide emissions. Zeolite, which reduces permeability, is a typical concrete ingredient that strengthens and lasts. Recently, natural zeolite has become a prominent concrete pozzolanic component. For environmental preservation and sustainable development, various experiments were done on concrete with pozzolanic components partially substituting cement and compared to ordinary concrete. A partial replacement of cement with zeolite improves the properties of concrete up to a certain age and mixing ratio. More than 44 relevant articles from 2004–2024 were selected from 762 papers evaluated for this paper. This paper reviews natural zeolite research in real applications. Additionally, it provided a cutting-edge review of natural zeolite literature through a critical analysis of various previous investigations. It also helped to understand how zeolite influences concrete mixture workability, strength, and durability. Since zeolite is a major concrete ingredient, it should be promoted as a sustainable resource.
In this paper, the cross section behavior of reinforced concrete columns made of normal and hybrid reactive powder concrete (hybrid by steel and polypropylene fibers) under concentric and eccentric vertical load was study. The casted columns were cured in two different type tap water for 28 days and chloride water for six months. Chloride salts with concentration was 8341.6 mg/l. Three variables were adopted in the experimental program; concrete type, curing type and the eccentricity of vertical load. Twenty (120x120x1200) mm columns were casted and tested depending on these variables. The different eccentricities were (0, 50,100 and 150) mm and where (e/h) were (0, 0.42, 0.83 and 1.25) respectively from the center of column, the other types of loading are tested the specimens as beam._x000D_ The experimental results showed increasing in ultimate load capacity and higher chlorides resisting for hybrid reactive powder concrete in comparison with normal concrete in both types of curing (tap and chloride water). Through studying load deflection, test results for Normal Strength Concrete (NSC) and Hybrid Fiber Reactive Powder Concrete (HFRPC) columns that deflection for columns cured in chloride water more than tap water when compared at the same load that also by increase eccentricity leads to an increase in deflection for both cured and The neutral axis depth for HFRPC columns is more than NSC at the same load also when eccentricity increases, the compression zone decreases and neutral axis also decrease by increase eccentricity. These results occur when columns are cured in tap and chloride water._x000D_
In Republic of Iraq, ready-mix concrete production plants have been adversely affected by the lack of modern and advanced technology to assess their performance in line with technological advancements. Current evaluation methods rely on traditional approaches and financial measures, yielding unrealistic performance results. To address this problem, there is a need to utilize modern models and methods for performance evaluation. The study's main objective This was achieved by employing a literature survey methodology and utilizing digital databases such as the Iraqi Scientific Journals website, virtual libraries, and scientific platforms like ScienceDirect, Springer, Google Scholar, and Gate Research between 2015 and 2023. The research study provided a comprehensive overview of performance evaluation, including its definitions, importance, and an introduction to modern models and evaluation methods. The study found that no previous studies have been conducted in Iraq to evaluate ready-mix concrete production plants. However, four studies were found in Egypt, Sudan, and India. The previous similar relevant studies discussed various topics and related studies. Firstly, they discussed the classification, advantages, and disadvantages of concrete mixing plants. Additionally, the previous studies analyzed the factors that most influence the performance of concrete production plants, including laboratory manager efficiency, work team efficiency, communication and relationships within work teams, plant operator, material transportation method, and time and courses. Furthermore, the previous research studies present a comprehensive analysis of all variable data simultaneously using the statistical package for Social Science (SPSS) input stage. The evaluation also extends to the evaluation of laboratories, encompassing plant arrangement, internal quality control systems, and final product quality. The overall evaluation results of previous studies. Indicate that 75% of the concrete production plants failed to meet the required criteria, while only 25% demonstrated satisfactory performance. The study proposed improvements to enhance the performance rate of ready-mix concrete production plants by leveraging the most influential variables, which will be considered in the study.
This research submits theoretical and experimental realization of shear behavior of RC I-beams with polypropylene fiber with different volume fraction of plastic fiber as additive. The enhance of the sustainability of structural elements through the development of its mechanical performance by adding new materials such as plastic raw materials has become more important in the current period , particularly I- beams that was used in the long spans structure to become more environmentally-friendly. Seven specimens were tested in this study and only the amount of fiber volume fraction was varied. Experimental results showed that the ultimate strengths are increased in range (4.4% to 35.27%) that of control IB-1 for the tested beams containing Polypropylene Fiber Reinforced Concrete (PPFRC) with varied amount percentage of fiber material. Crack arrest mechanism of polypropylene fibers, and compressive strength of concrete increased in range (7.42% to 29.3%) that of plain concrete, and improved the tensile response in range (8.36% to 92.7%) that of plain concrete, limited crack propagation. So, improved behavior was obtained._x000D_ ANSYS 11, Finite Element models software are used to emulate two tested I-beams. 3D - nonlinear solid elements was utilized to model the concrete, while, the steel reinforcement was demonstrated by spar element. It was found that the general practices of the FE models demonstrated acceptable concurrence with perceptions and information from the experimental tests.
Most of building rubbles or wastes contain some damaged materials such as cement, brick, steel, ceramic, plastic and other substances. Among these materials, ceramic and brick when using both of them as a partial replacement by the weight of conventional coarse aggregate in mixture concrete with presence of variety ratios ( 10% to 30%) for sawdust as replacement of fine aggregate, the resulting concrete properties will affected. So, this paper was based on the study some properties of concrete that produced of 50% replacement for those rubbles plus to presence 10%, 20% and 30% sawdust for both of them. The results revealed that present of sawdust with each of type of those rubbles provides database which are potential to be used in the production of lighter and economical new concrete material. Furthermore, the higher ratios of sawdust (more than 10 %) lead to obvious affected on the strength as well as other properties. While, those negative effects will perceptible improved when added 10% sawdust in ceramic aggregate concrete compared to brick aggregate concrete.
Normal concrete is weak against tensile strength, has low ductility and also insignificant resistance to cracking. The addition of diverse types of fibers at specific proportions can enhance the mechanical properties as well as the durability. Discrete fiber, which is commonly used, have many disadvantages such as balling the fiber, random distribution, and limitation of the used Vf ratio. Based on this vision, a new technique was discovered, enhancing concrete by textile-fiber to avoid all the problems mentioned above. This paper presents all important consequence and conclusions obtained from previous studies on how to strengthen concrete with two-dimensional and three-dimensional textile-fibers, and focuses on the flexural behavior of concrete members. The results indicate that there was an improvement in flexural strength, deformation capacity, and toughness with different load conditions when using different types of textile-fiber. It was observed that the effect of textile-fibers would increase when this fiber was coated by epoxy. In TRC system, there is a significant impact on the number of textile-fiber layers used.
CFDSST Concrete Filled Double-skinned steel tubular columns are composite columns consisting of two concentric circular steel tubes with concrete filler in between. Finite elements method is considered through the use of the computer program ABAQUS to model CFDSST columns numerically under cyclic axial compression. Damage plasticity model was considered to model the concrete while elastic-plastic model used to model the steel tubes. six CFDSST specimens and three ordinary Concrete Filled Steel Tubular (CFST) specimens were analyzed under static axial compression, while three CFDSST specimens were considered for analysis under cyclic axial compression. The numerical results were presented in terms of axial load axial strain displacement curves. It was found that the ultimate axial load carrying capacity calculated numerically in good agreement with that of the experimentally tested specimens. Also it was concluded that Damage plasticity model used for simulating the behavior of concrete and metal plasticity model used for simulating the behavior of steel produced accurate results as compared to the experimental results.
In term of sustainable practices, recycling plays a crucial role, particularly in the construction industry where the disposal of old structures generates significant waste. Recycling old concrete not only reduces the need for new natural resources but also eliminate waste accumulation. Numerous research study the behaviors of recycled aggregate concretes, practically focusing on the long term behaviours. A large number of studies have demonstrated that concrete made from recycled aggregate exhibits poorer long-term characteristics in comparison to aggregate from nature concrete. The long-term behaviour can be affected by three factor which is creep, shrinkage and tension stiffening. Greater management of these variables can enhance the RAC's long-term properties. The review will specifically focus on the influence of time dependent parameters i.e., creep, shrinkage, and loss of tension stiffening with time. Furthermore, it will explore the long-term deflection predicted from code used for deflection prediction, considering three codes: ACI, EC2, and the CSA code. The purpose of this paper is to enhance the understanding of long-term deflection of recycled aggregate concrete beam and evaluate the effectiveness of various factors that impact their structural performance.
This article provides a general up to date review of the investigation on performances and resistances of plain and fiber containing concrete structures under periodical loadings of long endurance up to fatigue failure. Structures are almost, under the frequent influences of repeated loadings such as vibrations of rotary machines, sea /river waves, wind, earthquakes and moving vehicles. Long term application of cyclic loading leads to continually slow rate degradation of the structure rigidity leading to fatigue damage. In spite of the dominant usage of concrete, worldwide, as a building material, its fatigue behavior is not straight forward. In addition, this lack of comparison is confronted for fiber fortified concrete. The article also presently a survey of the available techniques for monitoring and measurement of fatigue impressions in concrete structures founded both their impact within the treatise domain and the non-destructive inspection. Those technical means are classified into, at least, two designations, specifically, the monitoring of fatigue induced cracking and the detection of fatigue charged damage. Those techniques parameters, evaluate the changes in the mechanical and physical materials properties during the fatigue endurance, are distantly reviewed in concern of the mechanism creating the change, shortcomings, constraints, etc. The merits, dependency, feasibility, disadvantages and limitations of each technique are assessed and compared to make an index to select the appropriated e technique for fatigues fracture or failure inspection of the type fibered or not of structural concrete
In this vast world after an earthquake lessons are learned; many strategies have been considered in order to achieve a proper seismic strength capacity.The aim of this paper is studying the seismic behavior of a typical reinforced concrete bridge pier in Iraq and implementing a proper technique of strengthening in order to fix any damage that had happened.Structure of a full scale three-dimensional finite element model was used in order to simulate a reinforced concrete pier via the computer software ABAQUS/CAE 2017 using concrete plasticity damage model (CDP).Under the action of Halabja earthquake, which was recorded at city of Halabja in Iraq on 12 November 2017, the behavior of model was traced, analyzed and the resulted damages were managed.The finite element analysis results indicated that the proposed configuration of carbon fiber reinforced polymers laminates substantially increases the lateral load strength and deformation capacity of the bridge pier
In this work chopped carbon fibers are used to improve tensile strength of Porcelanite lightweight aggregate concrete. Silica fume was added in order to improve the mixes compressive strength. Silica fume increase water demand and using fibers reduce workability, to improve workability and decrease water demand high rang super plasticizers are used. The results showed that compressive strength, splitting tensile strength, modulus of elasticity of carbon fibers Porcelanite lightweight aggregate concrete increase with increasing of carbon fiber up to 2% compared to reference Porcelanite lightweight aggregate concrete without fibers. The percentages of increasing were 14.40%, 68.00%, and 10.66% for compressive strength, splitting tensile strength, and modulus of elasticity, respectively. Flexural Strength continues in increase with increase of fibers. The dry unite weight of mixes with chopped fiber decrease with increase of fiber percentage. Besides the chopped carbon improved the ductility of Porcelanite lightweight aggregate concrete and that clear from stress-strain relationship.
This paper present glass waste material reusing in concrete as partial replacement of cement. Some hardened properties like compressive and flexural strengths, modulus of elasticity and % absorption was made. The effect of glass powder on these properties was examined compared to reference specimens without glass powder. Five percentage was tested: 0%(reference), 10%, 15%, 20% and 25%. From tests results one can conclude that replacing cement partially by glass powder enhanced strengths of concrete (compression and flexural) up to 20% replacing level Using glass powder as partial replacement of cement improved strengths and modulus of elasticity of concrete. The %absorption decrease with increasing of glass powder content. The results show that utilization of waste glass as powder in concrete can reduce amount of cement which save cost besides its environmental benefits.
In this work, waste glass powder from broken windows and plastic fibers from waste polyethylene terephthalate bottles are utilized to produce an economical self-compact concrete. Fresh properties (slump flow diameter, slump Flow T50, V. Funnel, L–Box), mechanical properties (Compressive strength and Flexural strength) and impact resistance of self-compact concrete are investigated. 15% waste glass powder as a partial replacement of cement with five percentages of polyethylene terephthalate plastic waste were adopted: 0% (reference), 0.5%, 0.75%, 1%, 1.25% and 1.5% by volume. It seems that the flow ability of self-compact concrete decreases with the increasing of the amount of plastic fibers. The compressive strength was increased slightly with plastic fiber content up to (0.75%), about 4.6% For more than (0.75%) plastic fiber. The compressive strength began to decrease about 15.2%. The results showed an improvement in flexural strength and an impact on the resistance in all tested specimens’ content of the plastic fibers, especially at (1.5%) fibers.
This paper presents a simple strut and tie model to calculate the shear strength of reinforced concrete deep beams. The proposed model assumes that the shear strength is the algebraic sum of three strength components: concrete diagonal strut, vertical stirrups, and horizontal web reinforcements. The contribution of each strength components was calibrated with the test results of 305 deep beams compiled from previous studies with wide range of geometrical and material properties. The predictions of the proposed model were compared with those of the current codes of practice (ACI-318-14 and ASHTOO 2014) and those of existing model in the literature. Comparisons revealed that the proposed model provided better predictions than other models. The mean of predicted strength to test of the proposed model, the ACI-318-14 model, the ASHTOO 2014 model were 0.98, 0.79, and 0.75, respectively. The corresponding standard deviations were 0.17, 0.28, and 0.49, respectively.
In this paper an experimental works conducted to study the behavior of R.C. beam with large web opening at different locations and fortified with reactive powder composite (RPC) at the extreme tension zone (bottom edge of opening) and/or extreme compression zone (Top edge of opening). The experimental study is investigate the behavior of twelve beams and study the ability of using normal strength concrete together with RPC in the same section to exploit the advantages of these two materials in optimal way. The main variables are RPC layers locations in tension zone and/or in compression zone and the locations of openings. The ultimate loads, load mid-span deflection behavior and strain for steel and concrete were discussed. The experimental results showed that the ultimate strength was decreased with increasing number of opening about 4% for beams with two openings located in shear zone and 21% for beams with three openings, thus indicating that the stiffness decreases accordingly. The using RPC layers effectively enhanced performance of hybrid beams when compared with using the normal strength concrete layers only. The using RPC layers in compression and tension zones increased the ultimate load about 47 % for beams with two opening located in shear zone, when using RPC in the tension zone and normal strength concrete in the compression zone the ultimate flexural load and ultimate deflection increase little compared with normal concrete.
Rigid pavement slabs are erected on a prepared subgrade or foundation layer, providing a hard and continuous surface. Transverse joints made of dowel bars connect them, and longitudinal joints made of tie bars join them longitudinally. This study is an investigation of the impact of soil strength and concrete parameters on the effectiveness of dowel bars in rigid pavements. Moreover, three parameters were examined; California Bearing Ratio (CBR), concrete compressive strength and slab thickness. The analysis was conducted using the Ever FE program and focused on several axle configurations applied to the joint. The results indicate inverse association between the pavement slab thickness and the concrete strength, under the assumption of consistent soil strength. Moreover, an assortment of reduced shear forces on the dowel bars is seen when the soil strength values increase. It indicates that soil strength has a greater impact on the shear load of dowel bars compared to the qualities of concrete. Additionally, the type of axles used and the magnitude of soil strength were shown to have a significant effect on the shear load.
Reinforced concrete slab with plastic voids (Bubbled Deck system) is a new type of slabs which has two-dimensional arrangement of voids within the slab that is developed to decrease the slab self-weight while maintaining approximately the same load carrying capacity as compared with the solid slabs. Plastic voided slabs have the ability to reduce concrete amount by about 30 percent and this reduction is so important in terms of cost saving and enhancement the structural performance. In this research paper investigation is carried out to study the shear strength behavior of one-way bubble deck slab using self-compacting reinforced concrete. The experimental program consists of testing thirteen one-way slabs with dimensions of (1700 length, 700 width and 150 thick) mm. One of the tested slabs is a solid slab (without balls) is used as a reference, the remaining twelve bubbled slabs with ball diameter (73, 60) mm are divided into five groups according to the parameters of the experimental work, the parameters of the experimental work include: type of slab (bubble and solid slabs), ball diameter (73, 60) mm, shear reinforcement and spacing between balls. The experimental results showed that the bubbled slabs without shear reinforcement have a decrease in the ultimate load as compared to solid slab by about 3.7% to 14.3% and an increase in the deflection at ultimate load by about 10% to 22%, at the same time the first crack load decreases by about 15.3% to 42.4% as compared to solid slab due to decreases of moment of inertia of bubble slab compared to solid slab. Also, the results showed that the bubbled slabs withe shear reinforcement (multi-leg) have an increase in the ultimate load as compared to solid slab by about 35.4% to 57.3% and an increase in the deflection at ultimate load by about 1% to 15%, at the same time the first crack load decreases by about 2.8% to 27.4% as compared to solid slab.
Searching for an optimal alternative to normal cement concrete (NCC) is an urgent need nowadays in order to reduce carbon dioxide emissions, reduce energy, and reduce waste materials. Therefore, this research aims to examine zero cement concrete (ZCC) slabs under monotonic loads with several paramedic studies including slab thickness (60mm, 80mm, 100 mm), bar spacing (75mm, 150mm, and 225mm), and molarity concentration (6M, 8M, and 10M). The results showed the behavior of reinforced ZCC slabs is similar to or slightly lower than that of normal cement concrete. Increasing slab thickness from 60 mm to 80 mm and 100 mm enhanced the slab stiffness, increased the applied loads, and reduced the vertical mid-span deflection. Decreasing bar spacing by 33.33% and 66.67% relative to 225 mm reduced also the deflection. The energy absorption was increased due to increasing the slab thickness and bar spacing. When the load increased, the slabs eventually failed by a typically visible punching cone (punching shear).
Lightweight foamed concrete (LWFC) is characterized as a light in self-weight, self-compacting, self-levelling, and thermal and sound isolation. But it has low strength and low ductility which leads that the application of (LWFC) in the building construction is limited. The flowability of the fresh mix of (LWFC) was evaluated by flow test. While the hardened properties of (LWFC) include, compressive6 strength, tensile6 splitting6 strength, flexural6 strength, and 6modulus of 6elasticity. This6 study6 focuses6 on the effect of the adding of silica fume and steel fibre on the mechanical properties of (LWFC). Silica fume was added as (5%) and (10%) by the weight of cement and steel fiber (0.2%) and (0.4%) of the total volume of the mix. The density of lightweight foamed concrete was 1800±50kg/ , and cement to sand ratio was (1:1) with water cement ratio (0.28). The results indicated that adding of silica fume6 and steel6 fiber6 have great effect on the mechanical properties and improve them. The addition (10%) of silica fume and (0.4%) by volume of steel fiber was the best ratio that improves the mechanical properties of the lightweight foamed concrete (LWFC). The pozzolanic index of the (5%) and (10%) silica fume was (21.9%) and (74.76%), respectively.
This paper presents experimental investigations to study the behavior of High Strength Reinforced Concrete (HSRC) deep beams with web openings under monotonic and static repeated loading conditions. The experimental work procedure consisted of testing eighteen simply supported HSRC deep beams both with and without web openings. The numerical work procedure consisted of testing ten simply supported HSRC deep beams both with web openings. All beams had the same dimensions and flexural reinforcement. They had an overall length of 1400 mm, a width of 150 mm and a height of 400 mm. The investigated test parameters were concrete compressive strength, shape and size of openings, vertical and horizontal reinforcement ratios, shear span to effective depth ratio (a/d ratio) and loading history. The experimental results reveal that the ultimate load capacities for specimens tested under four different repeated loading regimes decrease in the range between 2% and 19% in regards to the control specimens which were tested under monotonic loading regime. The results indicated that the increase in the severity of loading history leads to a decrease in the ultimate shear strength of the deep beams and causes increases in their ductility ratio. The ultimate loads of HSRC deep beams with square web openings size of (50*50mm, 60*60mm and 70*70mm) tested under the repeated loading history (HS-1) which consisting of five phases decreased by (11.4 %, 24.1% and 26.3 %, respectively) compared to that of identical solid deep beam. The ultimate load of HSCR deep beam with circular web openings shape tested under repeated loading history (HS-1) increases by 8.6 % compared to the equivalent square web openings shape. For numerically analyzed beams under repeated loading history (HS-1), the ultimate load increases by 16% when using area of 2500mm2 of circular web openings shape (equal in area to square web opening size 50mm*50mm) and by 13.5% when using rhombus web openings shape of the dimensions 50*50mm in comparison with the case of 60-mm size square web openings.
The main objective of the present paper is to investigate the effect of fineness moduli (FM) of fine aggregate on fresh properties (flow ability. Passing ability and segregation resistance), and hardened properties (compressive strength, split tensile strength, flexural strength and ultrasonic pulse velocity UPV) of self-compacting concrete (SCC). Four values of FM 2.3, 2.5, 2.7 and 3.1 were used, according to acceptance range of ASTM C33-03 for FM for fine aggregate, which recommended range for FM is 2.3 to 3.1._x000D_ Four series of mixes were casting , each series consist of two mixes represent normal strength and high strength SCC, each series of mixes made from fine aggregate have the same FM. Flow ability, passing ability.and segregation resistance of fresh SCC, both with normal and high strength decreases with increasing the fineness moduli. High strength SCC more effected than normal strength concrete due to increase the volume of particles. _x000D_ Great enhancement in compressive strength split tensile strength and flexural strength in both normal and high strength SCC when the FM is 2.5. Increase FM to 2.7 and 3.1 not lead to increase in strengths. The UPV values of normal and high strength SCC mixes have a good general condition. SCC mixes with FM 2.5 possess excellent general conditions.
Improving the ability of asphalt pavement to survive the heavily repeated axle loads and weathering challenges in Iraq has been the subject of research for many years. The critical need for such data in the design and construction of more durable flexible pavement in bridge deck material is paramount. One of new possible steps is the epoxy asphalt concrete, which is classified as a superior asphalt concrete in roads and greatly imparts the level of design and construction. This paper describes a study on 40-50 penetration graded asphalt cement mixed with epoxy to produce asphalt concrete mixtures. The tests carried out are the Marshall properties, permanent deformation, flexural fatigue cracking and moisture damage. Epoxy asphalt mixes performed better on resistance to fatigue and permanent deformation. They also performed significantly better on low-temperature properties and resistance to moisture damage. The addition of 30 percent of epoxy (by weight of asphalt cement) resulted in increase of Marshall stability by 39.8 percent, improve the tensile strength ratio by 22.9 percent, lowering both the rate of permanent deformation by 26.8 percent and the fatigue accumulation coefficient by 53.5 percent, in comparison with control HMA. Based on the above findings, it is recommended to use epoxy asphalt mixes as an optimal material for paving bridges deck in Iraq since it showed good prospects for this application due to the valuable performance and durability improvement.
Double skin composite (DSC) construction or Steel/concrete/steel sandwich construction (SCSS) is an innovative and relatively new form of composite construction that can be used in submerged tube tunnels, bridges deck, nuclear structures, liquid and gas containment structures, offshore and onshore structures, military shelters, and shear walls in buildings. The system consists of a plain concrete core sandwiched between two steel plates interconnected together by various types of mechanical shear connectors. The DSC construction perceives advantages that the external steel plates act as both formwork and primary reinforcement, and also as impermeable, blast and impact resistant membranes. The major duty of the shear connectors is to withstand longitudinal shear force and beam/slab separation, while in the bi-steel type where shear connectors are friction welded at both their two ends to two parallel steel plates, the longitudinal and transverse shear force, as well as plate buckling are resisted. The present paper highlights the previous prime researches concerning the subjects of SCSS composite construction, specifically on the conducted tests (push-out tests, tensile, direct shear tests, and bending tests) in which the components of partial interaction (uplift and slip forces) are resisted by various types of shear connectors.
Glass is an inert material which could be used and recycled many times. Several tons of waste glass (WG) are generated annually worldwide due to the rapid growth of the population and improvement in the standard of living. In this study, the WG was used and supplied with three different particle sizes; 600?m, 2.36 mm and 4.75mm and partially weight replaced of fine aggregate at ratios 10%, 20% and 30%. The effectiveness of that changes on compressive strength and modulus of rupture at ages 28 and 90 days for concrete specimens produced were studied. The results showed that compressive and modulus of rupture at all ages increased along with addition of WG as glass powder (GP). Moreover, the specimens containing 30% of GP replaced has the best results, also it is found at this percentage of GP, more beneficial and capable to increased compressive and flexural strength up to 18.64% and 5.87 % respectively at 28-day compared to reference specimen. Besides, the test results revealed that at a replacement level 10% of 2.36mm fine glass (FG) has slightly improved the strength characteristics. While, the results demonstrated decreasing in that properties for the concrete specimens contained on coarse glass (CG) up to 4.75mm. The maximum negative effect on compressive strength and modulus of rupture recorded at the ratio 30% of CG where was the reduction in compressive strength 28.52% opposite 22.12% for modulus of rupture at age of 28-day. From that results, it can be concluded that the effect of FG was little compared to GP.
Eight RC circular hollow columns (external diameter = 220 mm, internal diameter = 100 mm, length = 1000 mm and the hollow part = 700mm) casted and strengthened with ferrocement fibers composites to illustrate the behavior of these columns under concentric and eccentric axial compression force. Two columns where used as reference columns, which were repaired after failure to be tested as retrofitted columns. Six specimens were strengthened with one and two WWM layers as required. The variables considered included number of the WWM layers (N), the loading configuration and the eccentricity value (e) of loading. The ferrocement thickness was constant at 20 mm in all retrofitted and strengthened specimens.The test results revealed that the maximum increase in the ultimate concentric loads were 67% by strengthening the reference column with two layers of WWM, and the maximum increase in the ultimate eccentric load of columns was 78% by increasing of the WWM from one to two layers. For a constant number of WWM layers, the change from concentric to eccentric force caused a decrease in the ultimate load value attaining 73.5% for one- layer WWM strengthened columns. The failure of columns occurred by yielding of steel reinforcement followed by concrete crushing (i.e. tension failure).
Action of applied external loads, early thermal by hydration of cement in reinforced concrete (RC) structures, creep and shrinkage and seasonal effects due to environmental conditions are the main causes of inducing cracks in RC members. Most Design Codes of RC structures have underestimated the distribution steel requirements based on stating nominal or minimum requirements for early thermal and moisture movement especially in watertight continuous constructions. Three dimensional finite element analysis for a verification problem was carried out on a continuous reinforced concrete members with different bar diameter subjected to different applied temperatures values which represent the early-age and seasonal effects. The results of this analysis were compared with the available BS Code equations for crack control for early thermal movements. The comparison between the Code equation and finite element analysis was met in a good agreement. The resulted data was used to study parametrically the crack characteristics in terms of crack width and spacing of RC members in term of the effects of three different construction exposures (Class A, B and C), three values of temperatures with three different bar size diameter (10mm, 12, 16) for each one. The present work was indicated as the bar diameter increases, the required steel ratio increases proportionality to match the assumed crack width. So, to get the minimum steel ratio this is the target. It must use smallest bar diameter. But unfortunately this is limited by minimum practical bar spacing. The overall of present study was indicated that the continuous construction required high steel area especially for class A exposure.
Numerical analysis of the performance of reinforced concrete (RC) deep beam subjected to static and fixed-point pulsating loading at the midpoint has been investigated. Three-dimensional nonlinear finite element model using the Strut and Tie approach was adopted. The damage level under the influence of the applied fixed pulsating loading is higher than the static applied loading, hence early crack was observed because of the stepwise loading in the form of vibration. Although the Strut and Tie approach gave a good estimation of the resistance capacity of the beam, the beam undergo high shear damage when subjected to these two types of loading. Material strength properties, applied loadings and cross-sections adopted are some of the factors that affect the performance of the deep beam.
Due to the instability and irregular of national electric power supplied to residence sector in Iraq for long term history, attracted researchers interest to strive for solutions, and associated challenge dry and very hot summer season in Iraq on air conditioning application, A test room full size prototype was constructed in Baghdad, its size 33.5m3, the room is built from very good thermal insulation Autoclave Aerated Concrete AAC with white panted Concrete roof, test room is exposed to solar radiation during entire day, thermal energy shifted by time using thermal energy storage TES containing PCM, PCM is soft paraffin its phase inversion temperature (29 to 27)°C, thermal energy was shifted from night timing by cooling down TES (Discharging PCM) to peak time 11:00 am to 02:00 pm, the testes were carried out over entire summer season April to October, the results showed thermal energy can shift to by any quantity and time based on mass of PCM and enthalpy, electrical energy saved at peak time 52.5% of total power spent over season 2.7KW/day, Only 27% of electric energy utilized to discharge PCM during night, about 43% of heat lose is sourced from exposed roof, melting and solidification of PCM temperature must be within indoor comfort range 23 to 28 ?C to release or absorb the latent heat 41kJ/kg.
The composite opened web steel joist supported floor systems have been common for many years. It is economic and has light weight and can embed the electrical conduit, ductwork and piping, eliminating the need for these to pass under the member, consequently eliminate the height between floors. In order to study the joist strength capacity under the various conditions, it had been fabricated seven joists composed of the steel and concrete slab connected to the top chord by shear connectors (headed studs). These joist have 2820 mm length c/c of the supports and 235 mm overall depth. In the present study, six variable parameters are adopted (Studs distribution, Degree of shear connection, Degree of the web inclination, Shape of the web, Density of concrete for slab and length of the shear connector). The test results exhibited that minimum strength capacity was 160kN for light weight joist and maximum capacity was 225kN for joist of long shear connectors at failure. The results were compared by ultimate flexural model by Azmi.
This research was conducted to investigate the effect of using internal steel plates for shear reinforcement on flexural behavior of SCC beams instead of using traditional reinforcement bars (stirrups) and to study the effect of their spacing and thickness on strength. The experimental work included destructive tests on six SCC beams under two-point load. The results showed that the yield loads in all of the beams with steel plates were lower than the reference beam by (5.21%) on average, the deflection at yield load was higher by (13.72%) on average and the ultimate loads were lower by (6.77%) on average except in one beam where it was higher by (0.37%). It was also found that the ultimate deflection in beams with internal shear steel plates was lower by (10.01%) on average except in the aforementioned beam where it was higher by (2.31%). Ductility in all beams with steel plates was lower by (20.08%) on average and the strain before a load of (200kN) was higher in the longitudinal reinforcement and lower in shear steel plates and vice versa after a load of (200kN). Theoretical analysis was also carried out for all beams using the finite element program ANSYS (version 15) where theoretical results of load versus mid-span deflection relations, longitudinal reinforcement strain, shear reinforcement strain, variations of neutral axis depths and cracks patterns showed good agreement with experimental ones. Finally, some specific further studies were recommended.
This paper presents a numerical investigation to study the effect of variations in displacement history sequence and magnitude on cyclic response of RC tapered (haunched) beams (RCHBs).Five simply supported RCHBs (four haunched and one prismatic) were selected from experimental work carried out by Aranda et al. The selected variables included were five loading history types. The first part of this study focused to verify the finite element analysis with selected experimental work and the second part of this study focused too studying the effect of varying in loading history to the response of RCHBs. The finite element code Abaqus was used in the modeling. The adopted cyclic simulation performance of the selected beams using the plastic- damage model for concrete developed by Lubliner and Lee & Fenves. The constitutive model of plain concrete describing the uniaxial compression response under cyclic loading proposed by Thorenfeldt, and the uniaxial tension response follows the softening law proposed by Hordijk was used in the modeling. Menegotto-Pinto model was used to simulate the steel response. Model verification has shown A good agreement to the selected experimental work. The variations in loading history will decrease the ultimate load and corresponding deflection with increase in the number of cycles at ultimate load.
Openings in reinforced concrete (RC) slabs are usually created as a result of variations in construction function, architectural or mechanical necessities. Heavy equipment loads resulting from mechanical system of any building are often carried by RC slabs. Even the static analysis and design of RC slabs with opening is not clearly stated in the available international Codes, dynamic analytical solution for such structure is complex._x000D_ In this paper, numerical analysis based on finite element approach is utilized to implement the modal analysis of RC slabs. Opening size and position was parametrically studied. Slab natural frequency or periods in addition to, the mode shape were registered. The results showed that the opening size and position involved in RC slab had a significant change in the value of natural frequency and period for the high level modes. The material nonlinearity affect on free vibration analysis of RC opening slab with different levels of stiffness modifiers was taken into account. The dynamic characteristics of RC opening slab as a function of stiffness modifier degree was numerically measured for six mode shapes. The paper found that a reduction in stiffness modifier value greatly reduce the .natural frequency of RC opening slab.
This study concerns utilization of nonlinear finite element method for to evaluate the role of longitudinal soffit-bonded CFRP strips in elevating the shear behavior of RC beams without stirrups. All beams cross-sections were of 150 mm breadth and 200 mm depth, the overall length was 1500 mm with clear span 1300 mm. One beam was provided by minimum web reinforcement according to the ACI 318M-14, while the other five were without web reinforcement but externally strengthened by a variety of CFRP-strip combinations consisting of longitudinal soffit-bonded strips. The predictions of a proposed ANSYS (version 14.5) model for six of the test beams including modeling of concrete, steel rebars, CFRP strips and supports and loading steel plates, by SOLID65, LINK180, SHELL41 and SOLID185 elements, respectively, show high agreements with experimental evidence, which stands as a definite witness to the efficiency and reliability of the present numerical model.
Behavior of composite beams with headed stud shear connectors subjected to monotonous and displacement controlled non-reversible repeated loadings has been evaluated through studying influences of the cross-sectional proportioning, the degree of partial interaction, and the level of ductile deformability in the post-yielding stage, in addition to the state of loading (whether monotonous or repeated). Eleven one- third scaled composite beams (with their push-out segments) were manufactured and tested in five pairs (each comprising the two loading cases representing one varying studied parameter) beside the single standard composite beam dedicated to verify accuracy of the test results by comparing them to the prototype ones (three authorized experimental and analytical investigations) where no distinction (other than 7 % difference) between the results of the three authorized refereed investigations (experimental, analytical and Eurocode) and the present one.Regarding the flexural resistance in repeatedly loaded composite beams, it has been found that lowering the neutral axis (by adding bottom steel plate) has significantly increased the beam flexural resistance by an average of 24.7 %. Meanwhile, the intensity of headed studs distribution in stiffened repeatedly loaded composite beams has revealed a vital role in controlling the severity of the post-ultimate flexural weakening, where decreasing number of the headed studs to the half has increased the value of that unfavorite parameter by 160.58%. Furthermore, that specified decrease of headed stud intensity has lowered the advantageous residual cyclic flexural ductility by 19.37 % and 11.48 % without and with stiffening bottom steel plates, respectively. Regarding the effect of the lengthening the headed stud on behaviour of the repeatedly loaded composite beams it has been found that lengthening the medium-length headed studs by 72% has raised the flexural stiffness by 41.1 %, while it has decreased the residual cyclic slippage index by 54.3 %.
A tack coat is a minimal coating of asphalt cement, cut-back asphalt, or asphalt emulsion to an existing pavement surface between layers to guarantee proper bonding between the two layers and longitudinal and transverse joints. Numerous researchers have assessed interlayer adhesion employing failure-mode behavior tests, such as pull-off, direct shear, and torsion testing. This study aims to quantify the best tensile resistance obtained using three types of cutback asphalt (RC70, RC800 modified with polymer 4.5% & MC70). All are applied on concrete surfaces at a rate of 0.5 L/m². The Proceq DYNA Z16 pull–off tester is used to measure the tensile strength at a rate of 0.25 kN/s. It is found that the average tensile strength of the tack coat materials is (0.319, 0.138, 0.028) MPa, respectively. It is concluded that RC70 has the maximum tensile strength. Also, the different types of solvent affect adhesion strengths; RC70 was Prepared using gasoline, while MC70 used petroleum. Gasoline has greater volatility and thus increased adhesion. Failure strength modes of interior bonding varied between cohesive failure adhesive and adhesive failure.
This paper studies the effect of different design spectral response acceleration parameters as suggested by the uniform building code (UBC), unified facilities criteria (UFC), and Iraqi seismic code(1997) (ISC 97) on the seismic response of reinforced concrete multi-story framed building located in Baghdad city, Iraq. These parameters are: (a) spectral response accelerations Ss, at short periods, and S1 at a 1-second period in accordance with international building code (IBC), (b) seismic zone factor (Z) according to UBC, (c) Seismic hazard zoning coefficient (Z) according to ISC 97. In this paper, first, the elastic seismic responses for significant modes of vibration for chosen building under design response spectrum that obtained from the above mentioned codes are calculated, and then a comparison was made among different design spectral response acceleration parameters. The intent of this study is to review the seismic provisions of the current edition of Iraqi seismic code (1997) to determine whether it provides an equivalent level of safety to that contained in other international codes. Design base shears, lateral seismic forces, inter story drifts, response spectrum modal, effective seismic modification, floors acceleration and story shears are comparatively presented.
This paper focused on evaluating the effect of aggregate gradation and polymer modification on indirect tensile strength (ITS) and the static stiffness for hot asphalt mixtures. In particular, data from ITS tests have been processed to obtain stiffness measurements through the application of Hondros theory. The results showed that fine mixtures had a better tensile strength by 26.3% than the coarse mixtures. The effect of compaction also was examined, the results showed that samples compacted with the Superpave gyratory compactor (SGC) had an enhancement in ITS by 36.58 and 23.1% in comparison with Marshall and roller compactor respectively. Polymer modifiers were used to estimate their effect on tensile strength, adding 4, 6, and 8% of Styrene-Butadiene-Styrene (SBS), which can rise the ITS by 3.2,6.14 and 13.3% of the non-modified asphalt mixture. Furthermore, using 4, 6, and 8 percent of SBS could increase static stiffness by 53.9, 209.6, and 302.4% respectively for roller compacted fine mixes and 58, 220, and 379.3% for SGC compacted mixes. Furthermore, SBS raised the stiffness modulus by 52.3, 188, and 295% for Marshall compacted mixes. Using hybrid modifier can improve the stiffness of the asphalt mixture. However, The results indicate that using 1, 2 and 3% polyvinyl chloride (PVC) can magnify the stiffness of mixtures by 41.2, 199.8% and 262.6 for roller compacted mixtures and 133.4, 212.1 and 354% for SGC compacted mixtures, whereas there is a stringent increasing by 133.4, 189.2 and 354% for Marshall compacted mixes. Otherwise, polymer-modification can decrease the fracturing index for coarse and fine mixtures.
In Iraq some pavements of the newly constructed highway appear precocious distresses with unfavorable implications especially on the safety and the frugality. Cracking and permanent deformation are main types of these failures. The filler is doubtful to be a master contributor to these failures where its content has a significance effect on the mixture stiffness, and thereby affect the HMA pavement performance. The main objective of this research is to appreciate the influence of different contents of filler on the volumetric properties of asphaltic mixtures thus performance of asphalt mixtures through Comparative Evaluation between conventional Marshall Method and Super pave system. The implementation of a detailed experimental work is carried out to achieve the study objectives through the preparation of asphalt concrete samples using aggregate from Al-Nebaie quarry, (40-50) asphalt cement from Dourah refinery and limestone dust filler with four different contents of (0%, 4%, 8%, and 12%) by weight of the total aggregate. The volumetric properties for each mix design method are evaluated using Marshall Test and the Super pave Gyratory Compacter. The influence of filler contents on the rendering of these mixtures was evaluated.
In this study, the analytic model (Azmi Model) had been considered for computation the load capacities of the composite open web steel joists and compared them with those obtained from experimental tests. The capacities of seven joists had been studied, each including one of the following variables (distribution of headed studs, connection degree of the connectors, inclination of the web, shape of the web, density of slab concrete, length of connectors).Theoretically, according to the Analytic model, the referenced joist of (45° web inclination , uniformly distributed ,over connected ,short headed studs) exhibited maximum load capacity of (18.45) ton, while the joist of (45° web inclination, uniformly distributed, under connected, short headed studs) exhibited minimum load capacity of (16.23) ton at yield point of bottom chord. Experimentally, the referenced joist exhibited maximum load capacity of (15.51) ton, while the joist of (34° web inclination, uniformly distributed, over connected, short headed studs) exhibited (12.49) ton load capacity. The load capacities values of the tested joists ranged between (67%-85%) of the predicted values according to the analytic model.
Open graded asphalt mixture is becoming more widespread where it is applied for various purposes, e.g. drainage of rainwater effectivity, traffic safety (high skid resistance), and controlling pollution noise. However, it has many other disadvantages, of which low stability, high stripping, and moisture sensitivity. The research aims to study the effect of styrene butadiene styrene SBS addition on the volumetric and mechanical properties of open graded mixture. In this research one type of aggregate with gradation (12.5 mm NMAS), asphalt of penetration grade (40/50), and cement as filler were used. Optimum asphalt content was selected based on the criteria of air voids content, asphalt drain down, permeability, and abrasion resistance (for aged and un-aged) samples. Other properties of open-graded mixtures, such as indirect tensile strength (ITS), moisture susceptibility, Marshall stability and flow were evaluated. The results show that addition of polymer (SBS) leads to an enhancement in the properties of the modified mixtures. There is an improvement in Marshall parameters. Also, a slight decreasing is noticed for permeability and air voids. For Cantabro abrasion loss (aging and un-aging condition), the abrasion resistance is increased, the drain down of asphalt is decreased from original mixture by addition of SBS. Finally, the moisture sensitivity is improved indicating that modified mixes becomes more resistant to water damage.
In this study, previous researches were reviewed in relation to the seismic evaluation and retrofitting of an existing building. In recent years, a considerable number of researches has been undertaken to determine the performance of buildings during the seismic events. Performance based seismic design is a modern approach to earthquake resistant design of reinforcement concrete buildings. Performance based design of building structures requires rigorous non-linear static analysis. In general, nonlinear static analysis or pushover analysis was conducted as an efficient instrument for performance-based design. Pushover analysis came into practice after 1970 year. During the seismic event, a nonlinear static analysis or pushover analysis is used to analyze building under gravity loads and monotonically increasing lateral forces. These building were evaluated until a target displacement reached. Pushover analysis provides a better understanding of buildings seismic performance, also it traces the progression of damage and failure of structural components of buildings.