×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerConstruction joints are separations between successive concrete pours. They are critical in the building of large concrete structures, since these structures cannot be cast in a single pour. Self-consolidation concrete is a relatively new kind of concrete that is considered suitable for a wide range of construction applications, especially those needing a high early resistance. Certain findings from earlier experimental tests were adopted and analyzed using finite element analysis. ANSYS program was used to analyze the impact of utilizing high strength concrete (fc') and the secondary reinforcement ratio (ρv) on the behavior of reinforced self-consolidating concrete beams having a horizontal construction joint. Nine beams analyzed in this study have the same dimensions (150×180×1200) mm (width× height ×length). Between the two supports, the clear span was 1100 mm. Two-point loads were applied to the simply supported beams during testing. One of the beams acts as a control beam (without a construction joint) and the remaining beams were with horizontal construction joint in the tension zone. The ultimate loads obtained analytically vary by between 3.1% and 7.8 % from those found experimentally. The presence of the horizontal construction joints made the beam less stiff. Utilizing a 70 MPa high strength concrete resulted in a 47.4 % in ultimate load over the experimental value for regular strength concrete (28 MPa). Increasing the ratio of secondary reinforcement (0.01229 to 0.049) resulted in a 10.3% increase in ultimate load magnitude, while decreasing the ratio of secondary reinforcement (0.01229 to 0.0025) with spanning the spacing between stirrups led to a reduction in ultimate load magnitude by 55.8%.
In this vast world after an earthquake lessons are learned; many strategies have been considered in order to achieve a proper seismic strength capacity.The aim of this paper is studying the seismic behavior of a typical reinforced concrete bridge pier in Iraq and implementing a proper technique of strengthening in order to fix any damage that had happened.Structure of a full scale three-dimensional finite element model was used in order to simulate a reinforced concrete pier via the computer software ABAQUS/CAE 2017 using concrete plasticity damage model (CDP).Under the action of Halabja earthquake, which was recorded at city of Halabja in Iraq on 12 November 2017, the behavior of model was traced, analyzed and the resulted damages were managed.The finite element analysis results indicated that the proposed configuration of carbon fiber reinforced polymers laminates substantially increases the lateral load strength and deformation capacity of the bridge pier
The aim of this study was to support surgeons to decide where to place the screws in order to achieve an optimal fracture healing and to prevent implant failure after a femoral shaft fracture So this paper focus on the analysis of bone-plate construct by using Finite element Analysis (FEA), comminuted femur fractured bone fixed with Dynamic Compression Plate (DCP) 16 holes by 4.5 Cortex screws, to investigate the effects of screws configuration on the mechanical behavior of different seven model as Interfragmentary strain which is the most important factor for femur fracture healing. The results state the relationships between the Von-Mises stress, Total deformation and Interfragmentary strain with respect to the screws configuration. The study shows the regions of maximum stress from stress distribution and also founded that we can decrease the Interfragmentary strain by increasing the number of screws.
The finite element method is one of the important methods in analyzing geotechnical engineering problems; its main advantage is the ability to apply for the materials exhibiting non-linear stress-strain behavior. In this study the finite element program PLAXIS 3D 2013 is used to study the behavior of the piles under the influence of seismic waves in saturated sandy soil and the effect of adding geogrid with the pile foundation. The program has been used to facilitate the representation of the real model, input the required soil parameters and implementation of seismic data. Seismic wave, the soil geometry and the pile dimensions were fixed in all models, while dimension and depth of the geogrid used were varied to study the influence of different depth and dimension in reducing the pile displacements and the pore water pressure of soil. The results show that The reduction in settlement ratio (the difference between settlement of pile without and with using geogrid to the settlement without using geogrid) for ( ×L/2), (L×L) and (2L×2L) are 10.6%, 17% and 21.3% respectively. And the settlement ratio for geogrid at depths 8.33% and 12.5% of pile length are 9.6% and 17% respectively.