×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerReinforced concrete slab with plastic voids (Bubbled Deck system) is a new type of slabs which has two-dimensional arrangement of voids within the slab that is developed to decrease the slab self-weight while maintaining approximately the same load carrying capacity as compared with the solid slabs. Plastic voided slabs have the ability to reduce concrete amount by about 30 percent and this reduction is so important in terms of cost saving and enhancement the structural performance. In this research paper investigation is carried out to study the shear strength behavior of one-way bubble deck slab using self-compacting reinforced concrete. The experimental program consists of testing thirteen one-way slabs with dimensions of (1700 length, 700 width and 150 thick) mm. One of the tested slabs is a solid slab (without balls) is used as a reference, the remaining twelve bubbled slabs with ball diameter (73, 60) mm are divided into five groups according to the parameters of the experimental work, the parameters of the experimental work include: type of slab (bubble and solid slabs), ball diameter (73, 60) mm, shear reinforcement and spacing between balls. The experimental results showed that the bubbled slabs without shear reinforcement have a decrease in the ultimate load as compared to solid slab by about 3.7% to 14.3% and an increase in the deflection at ultimate load by about 10% to 22%, at the same time the first crack load decreases by about 15.3% to 42.4% as compared to solid slab due to decreases of moment of inertia of bubble slab compared to solid slab. Also, the results showed that the bubbled slabs withe shear reinforcement (multi-leg) have an increase in the ultimate load as compared to solid slab by about 35.4% to 57.3% and an increase in the deflection at ultimate load by about 1% to 15%, at the same time the first crack load decreases by about 2.8% to 27.4% as compared to solid slab.
Construction joints are separations between successive concrete pours. They are critical in the building of large concrete structures, since these structures cannot be cast in a single pour. Self-consolidation concrete is a relatively new kind of concrete that is considered suitable for a wide range of construction applications, especially those needing a high early resistance. Certain findings from earlier experimental tests were adopted and analyzed using finite element analysis. ANSYS program was used to analyze the impact of utilizing high strength concrete (fc') and the secondary reinforcement ratio (ρv) on the behavior of reinforced self-consolidating concrete beams having a horizontal construction joint. Nine beams analyzed in this study have the same dimensions (150×180×1200) mm (width× height ×length). Between the two supports, the clear span was 1100 mm. Two-point loads were applied to the simply supported beams during testing. One of the beams acts as a control beam (without a construction joint) and the remaining beams were with horizontal construction joint in the tension zone. The ultimate loads obtained analytically vary by between 3.1% and 7.8 % from those found experimentally. The presence of the horizontal construction joints made the beam less stiff. Utilizing a 70 MPa high strength concrete resulted in a 47.4 % in ultimate load over the experimental value for regular strength concrete (28 MPa). Increasing the ratio of secondary reinforcement (0.01229 to 0.049) resulted in a 10.3% increase in ultimate load magnitude, while decreasing the ratio of secondary reinforcement (0.01229 to 0.0025) with spanning the spacing between stirrups led to a reduction in ultimate load magnitude by 55.8%.
Structural elements. This means the structural behavior can be quantified by considering the behavior of each structural element in each load path. Concrete is a material known for its great strength. Regardless, there are a few weaknesses, which must be taken in consideration in the design of concrete structural elements. Basically, concrete is made of three main ingredients: Portland cement, water, and aggregates (sand and stone).In order to improve tensile strength and ductility (capacity to stretch and deform prior to failure) in concrete, so this paper discus some types of concrete and record the effect on beams. Reactive powder concrete (RPC) is an actual concrete mixture, it is a special type of concrete because mix concrete (coarse and fine aggregate ) replaced by fine sand size (150-400)µm. In the experimental comparison the mechanical properties( compressive , splitting tensile and flexural )strength of plain RPC and high and normal strength concrete. Each set consisted of (4) cubes of (100×100×100_mm, (8) cylinder of (150×300mm) and (4) prism of (100x100x500) mm and consisted of (4) beam of (1000×100×400)mm. The results shown that the maximum compressive strength is 107 MPa and the maximum splitting tensile 9 MPa of RPC comparison high and normal strength concrete. The result of the second part shown increased RPC reinforced concrete the firstcrack288 MPa and ultimate crack 380MPa comparison high and normal strength concrete and the mode of failure of RPC (flexural-shear).