Experimental Investigations of the Plasma Arc Cutting of AISI 1020 Carbon Steel Plate
DOI:
https://doi.org/10.29194/NJES.27020193Keywords:
Plasma Arc Cutting, Microstructure, MicrohardnessAbstract
The current study presents the plasma cutting process of 2 mm thickness of AISI 1020 carbon steel. The experiment conducted by taking into the account the effect of two process parameters, including cutting current of 15 and 20 A with cutting speed in range of 500 - 4000 mm/min, on the kerf formation, microstructure and microhardness.
The results showed that at low cutting current of 15 A the melting occurred at the workpiece surface without cutting action. Increase the current to 20 A led to full penetration of the workpiece material at low and high cutting speed, with kerf width between 1.26 mm and 1.1 mm for cutting speed of 500 mm/ min and 4000 mm/ min, respectively. The plasma arc cutting speed has a high impact on the heat-affected zone HAZ and microstructure development with coarse grains at the HAZ at low cutting speed of 500 mm/min and constant current of 20A, increase the plasma cutting speed led to decreasing the grain size. The microstructure of the HAZ exhibited a presence of perlite and ferrite with some martensite structure. The highest microhardness of the HAZ of 220.8 HV was found in the sample processed at 20 A current and high cutting speed of 4000 mm/ min. However, the minimum microhardness of the HAZ of 156.7 HV was found in the sample processed at 20 A current and low cutting speed of 500 mm/ min.
Downloads
References
Das, Partha Protim, and Shankar Chakraborty. "A comparative assessment of multicriteria parametric optimization methods for plasma arc cutting processes." Decision Analytics Journal 6 (2023): 100190. https://doi.org/10.1016/j.dajour.2023.100190
Sharma, Khushboo, Jai Kishan Sambharia, and Alok Khatri. "Optimization of Process Variables in Plasma Arc Machining of Inconel-718 Alloy Using Taguchi with Grey Relational Analysis." Advances in Manufacturing Processes: Select Proceedings of RAM 2020. Singapore: Springer Singapore, 2020. 37-58. https://doi.org/10.1007/978-981-15-9117-4_4
Ramakrishnan, S. and Rogozinski, M.W. Properties of electric arc plasma for metal cutting. Journal of Physics D: Applied Physics, 30(4), p.636. 1997 https://iopscience.iop.org/article/10.1088/0022-3727/30/4/019/meta
Chamarthi, S., Reddy, N.S., Elipey, M.K. and Reddy, D.R., 2013. Investigation Analysis of Plasma arc cutting Parameters on the Unevenness surface of Hardox-400 material. Procedia Engineering, 64, pp.854-861. https://doi.org/10.1016/j.proeng.2013.09.161
Bhowmick, S., Basu, J., Majumdar, G. and Bandyopadhyay, A., 2018. Experimental study of plasma arc cutting of AISI 304 stainless steel. Materials Today: Proceedings, 5(2), pp.4541-4550. https://doi.org/10.1016/j.matpr.2017.12.024
Özek, C., Çaydaş, U. and Ünal, E., A fuzzy model for predicting surface roughness in plasma arc cutting of AISI 4140 steel. Materials and Manufacturing Processes, 27(1),pp.95-102.2012 https://doi.org/10.1080/10426914.2011.551952
Rana, K., Kaushik, P. and Chaudhary, S. Optimization of plasma arc cutting by applying Taguchi Method. International Journal of Enhanced Research in Science Technology & Engineering, ISSN, pp.2319-7463.2013 https://www.erpublications.com/our-journals-search.php
Naik, D.K. and Maity, K.. Experimental analysis of the effect of gas flow rate and nature on plasma arc cutting of hardox-400. Welding in the World, 64, pp.345-352. 2020 https://doi.org/10.1007/s40194-019-00836-8
Duplák, J., Hatala, M., Dupláková, D. and Botko, F., 2019. Prediction model of surface roughness parameters of structural steel created by plasma arc cutting via full factor experiment. Materialwissenschaft und Werkstofftechnik, 50(10), pp.1207-1220. https://doi.org/10.1002/mawe.201900032
Hema, P. and Ganesan, R., 2020. Experimental investigations on SS 304 alloy using plasma arc machining. SN Applied Sciences, 2, pp.1-16. https://doi.org/10.1007/s42452-020-2350-y
Lazarevic, A., 2014. Experimental research of the plasma arc cutting process. Journal of Applied Engineering Science, 12(4). https://doi.org/10.5937/jaes12-6778
Aldazabal, J., Martín-Meizoso, A., Klimpel, A., Bannister, A. and Cicero, S., 2018. Mechanical and microstructural features of plasma cut edges in a 15 mm thick S460M steel plate. Metals, 8(6), p.447. https://doi.org/10.3390/met8060447
Ramakrishnan, H., Balasundaram, R., Ganesh, N. and Karthikeyan, N., 2018. Experimental investigation of cut quality characteristics on SS321 using plasma arc cutting. Journal of the Brazilian society of Mechanical Sciences and Engineering, 40(2), p.60. https://doi.org/10.1007/s40430-018-0997-8
Cinar, Z., Asmael, M. and Zeeshan, Q.. Developments in plasma arc cutting (PAC) of steel alloys: a review. Jurnal Kejuruteraan, 30(1), pp.7-16. 2018 doi.org/10.17576/jkukm-2018-30(1)-02
Ramakrishnan, H., Balasundaram, R., Ganesh, N. and Karthikeyan, N., 2018. Experimental investigation of cut quality characteristics on SS321 using plasma arc cutting. Journal of the Brazilian society of Mechanical Sciences and Engineering, 40(2), p.60.
https://doi.org/10.1007/s40430-018-0997-8
Ramakrishnan, S., Shrinet, V., Polivka, F.B., Kearney, T.N. and Koltun, P., 2000. Influence of gas composition on plasma arc cutting of mild steel. Journal of physics d: applied physics, 33(18), p.2288. https://iopscience.iop.org/article/10.1088/0022-3727/33/18/313/meta
Das, T., Erdogan, A., Kursuncu, B., Maleki, E. and Unal, O., 2020. Effect of severe vibratory peening on microstructural and tribological properties of hot rolled AISI 1020 mild steel. Surface and Coatings Technology, 403, p.126383. https://doi.org/10.1016/j.surfcoat.2020.126383
Çelik, Y.H., 2013. Investigating the effects of cutting parameters on materials cut in CNC plasma. Materials and manufacturing processes, 28(10), pp.1053-1060. https://doi.org/10.1080/10426914.2013.773015
Anakhov, S.V., Guzanov, B.N., Matushkin, A.V., Pugacheva, N.B. and Pykin, Y.A., Influence of plasma torch design on cutting quality during precision air-plasma cutting of metal. Steel in Translation, 50, pp.159-165.2020.
https://doi.org/10.3103/S096709122003002X
Cardona, D.M.M., Wongsa-Ngam, J., Jimenez, H. and Langdon, T.G., 2017. Effects on hardness and microstructure of AISI 1020 low-carbon steel processed by high-pressure torsion. Journal of Materials Research and Technology, 6(4), pp.355-360. https://doi.org/10.1016/j.jmrt.2017.05.002
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Samer Jasim Mahmood Algodi, Abdulhakeem Amer Salman
![Creative Commons License](http://i.creativecommons.org/l/by-nc/4.0/88x31.png)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
The authors retain the copyright of their manuscript by submitting the work to this journal, and all open access articles are distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC-BY-NC 4.0), which permits use for any non-commercial purpose, distribution, and reproduction in any medium, provided that the original work is properly cited.