Characterization and Fabrication of Ankle Foot Orthoses using Composite with Titanium Nanoparticles
DOI:
https://doi.org/10.29194/NJES.27010109Keywords:
Components Life Extension (Recycle), Cracked Shaft, Plastic Deformation, Laser Shock-Peening, Compressive Residual Stress, Mechanical Properties, Dislocation Strengthening MechanismAbstract
Orthoses and prostheses were Chosen and laminated based on their high Yield, ultimate stresses, bending stresses, and fatigue limit. Response Surface Methodology (RSM) was utilized to find the best values for two parameters reinforcement perlon fiber and percent of Titanium Nanoparticle coupled with the matrix resin during optimization. The response surface methodology combined the expertise of mathematicians and statisticians to construct and analyze experimental models. Using this method, we identified 13 different lamination samples comprising a wide range of perlon number and Ti nano Wt% in their Perlon layer composition. All lamination materials defined by RSM methods and produced by a vacuum system were subjected to a battery of tests, with fatigue tests performed on the ideal laminating material in contrast to laminations created in the first study (Tensile test, Bending test, and Fatigue tests according to the ASTM D638 and D790 respectively). In comparison to the other 12 laminations tested using Design Expert version 10.0.2, the lamination with ten perlon layers and 0.75 percent Ti nano proved to be the strongest overall in terms of Yield, ultimate, and bending loads. This study used composite materials and titanium nanoparticles to characterize and fabricate ankle foot orthoses. Strength in bending should amount to about 70 MPa, around 85 MPa in tensile tension. Two empirical quadratic equations for the models of peak bending strength and maximum tensile stress with 95% confidence were created using the response surface approach and analysis of variance within the design of experiments software.
Downloads
References
H. Uustal and E. Bearga, “Prosthetics and Orthotics,” in Sara Cuccurullo, M.D. (Physical Medicine and Rehabilitation Board Review), New York, USA: Demos Medical Publishing, 2002, pp. 409–489.
M. Natália and F. Martins, “Design of Ankle Foot Orthoses using Subject Specific Biomechanical Data and Optimization Tools,” in Instituto Superior Técnico, 2014.
M. Rahman, S. Zainuddin, M. Hosur, J. Malone, M. Salam, A. Kumar, and S. Jeelani, “Improvements in Mechanical and Thermo-Mechanical Properties of E-Glass/Epoxy Composites using Amino Functionalized MWCNTs,” Composite Structures, vol. 94, no. 8, pp. 2397–2406, 2012.
B. Bedaiwi and J. Chiad, “Vibration Analysis and Measurement in the Below Knee Prosthetic Limb Part I: Experimental Work,” in ASME 2012 International Mechanical Engineering Congress and Exposition, Proceedings (IMECE), 2012.
J. Chiad, “Study the Impact Behavior of the Prosthetic Lower Limb Lamination Materials due to Low Velocity Impactor,” in ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis (ESDA), 2014, pp. 25–27.
M. Al-Shammari, E. Hussein, and A. Oleiwi, “Material Characterization and Stress Analysis of a Through Knee Prosthesis Socket,” International Journal of Mechanical & Mechatronics Engineering (IJMME-IJENS), vol. 17, no. 6, 2017.
M. S. Al-Din Tahir and J. S. Chiad, “A Suggested New Material to Manufacture Above-Knee Prosthetic Socket Using the Lamination of Monofilament, Cotton, and Perlon,” Al-Nahrain Journal for Engineering Sciences (NJES), vol. 20, no. 4, pp. 832–837, 2017.
S. Abbas, K. Resan, A. Muhammad, and M. Al-Waily, “Mechanical and Fatigue Behaviors of Prosthetic for Partial Foot Amputation with Various Composite Materials Types Effect,” International Journal of Mechanical Engineering and Technology (IJMET), vol. 9, no. 9, pp. 383–394, 2018.
J. S. Chiad and M. S. al-Din Tahir, “A Suggested New Material to Manufacture Above-Knee Prosthetic Socket Using the Lamination of Monofilament, Cotton, and Perlon Fibers,” International Journal of Energy & Environment, vol. 8, no. 4, 2017.
M. Jweeg, Z. Hammoudi, and B. Alwan, “Optimized Analysis, Design, and Fabrication of TransTibial Prosthetic Sockets,” in IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, vol. 433, 2018.
A. Abdulameer and M. Al-Shammari, “Fatigue Analysis of Syme’s Prosthesis,” International Review of Mechanical Engineering, vol. 12, no. 3, 2018.
N. Yaseen, J. Chiad, and F. Abdul Ghani, “The Study and Analysis of Stress Distribution Subjected on the Replacement Knee Joint Components using Photo-Elasticity and Numerical Methods,” International Journal of Mechanical and Production Engineering Research and Development (IJMPERD), vol. 8, no. 6, pp. 449–464, 2018.
A. Takhakh and S. Abbas, “Manufacturing and Analysis of Carbon Fiber Knee Ankle Foot Orthosis,” International Journal of Engineering & Technology, vol. 7, no. 4, pp. 2236–2240, 2018.
A. Takhakh, S. Abbas, and A. Ahmed, “A Study of the Mechanical Properties and Gait Cycle Parameter for a Below-Knee Prosthetic Socket,” in IOP Conference Series: Materials Science and Engineering, 2nd International Conference on Engineering Sciences, vol. 433, 2018.
F. Kadhim, J. Chiad, and A. Takhakh, “Design and Manufacturing Knee Joint for Smart Transfemoral Prosthetic,” in IOP Conference Series: Materials Science and Engineering, International Conference on Materials Engineering and Science, vol. 454, 2018.
L. Yousif, K. Resan, and R. Fenjan, “Temperature Effect on Mechanical Characteristics of A New Design Prosthetic Foot,” International Journal of Mechanical Engineering and Technology (IJMET), vol. 9, no. 13, pp. 1431–1447, 2018.
J. Oleiwi and A. Hadi, “Experimental and Numerical Investigation of Lower Limb Prosthetic Foot Made from Composite Polymer Blends,” International Journal of Mechanical and Production Engineering Research and Development, vol. 8, no. 2, pp. 1319–1330, 2018.
M. Jweeg, A. Ahumdany, and A. Mohammed Jawad, “Dynamic Stresses and Deformations Investigation of the Below Knee Prosthesis using CT-Scan Modeling,” International Journal of Mechanical & Mechatronics Engineering (IJMME-IJENS), vol. 19, no. 1, 2019.
F. Kadhim, A. Takhakh, and A. Abdullah, “Mechanical Properties of Polymer with Different Reinforcement Material Composite That used for Fabricates Prosthetic Socket,” Journal of Mechanical Engineering Research and Developments, vol. 42, no. 4, pp. 118–123, 2019.
E. Abbas, M. Jweeg, and M. Al-Waily, “Fatigue Characterization of Laminated Composites used in Prosthetic Sockets Manufacturing,” Journal of Mechanical Engineering Research and Developments, vol. 43, no. 5, pp. 384–399, 2020.
F. Kadhim, J. Chiad, and M. Enad, “Evaluation and Analysis of Different Types of Prosthetic Knee Joint Used by above Knee Amputee,” Defect and Diffusion Forum Journal, vol. 398, 2020, pp. 34–40.
F. Kadhim, A. Takhakh, and J. Chiad, “Modeling and Evaluation of Smart Economic Transfemoral Prosthetic,” Defect and Diffusion Forum Journal, vol. 398, 2020, pp. 48–53.
A. Mohammed, E. Al-Hassani, and J. Oleiwi, “The Nanomechanical Characterization and Tensile Test of Polymer Nanocomposites for Bioimplants,” in AIP Conference Proceedings, 2019.
M. Al-Shammari, Q. Bader, M. Al-Waily, and A. Hasson, “Fatigue Behavior of Steel Beam Coated with Nanoparticles under High Temperature,” Journal of Mechanical Engineering Research and Developments, vol. 43, no. 4, pp. 287–298, 2020.
M. Al-Waily, M. Al-Shammari, and M. Jweeg, “An Analytical Investigation of Thermal Buckling Behavior of Composite Plates Reinforced by Carbon Nano Particles,” Engineering Journal, vol. 24, no. 3, 2020.
E. Ahmed, A. I. Rabea, and N. Tasnim, “Nanoparticles incorporation into polymeric materials for potential improvement in the mechanical properties: A review,” Journal of Polymer Research, vol. 27, no. 1, 2020.
M. Rajan, H. El-Hamshary, and A. Al-Dhamin, “Mechanical and Tribological Properties of UHMWPE Hybrid Composites Reinforced with Halloysite Nanotubes and Graphene Oxide,” Polymers, vol. 13, no. 3, 2021, p. 414.
B. D. Khandagale and U. V. Pise, “Numerical and experimental investigation of hinged Ankle-Foot-Orthoses (AFO) using composite laminate material for Cerebral Palsy patient,” Materials Today: Proceedings, vol. 62, pp. 2070–2080, 2022.
G. Rogati et al., “A novel apparatus to assess the mechanical properties of Ankle-Foot Orthoses: Stiffness analysis of the Codivilla spring,” Journal of Biomechanics, vol. 142, p. 111239, 2022
F. S. Shahar, M. T. H. Ameed Sultan, S. N. A. Safri, M. Jawaid, A. R. Abu Talib, A. A. Basri, and A. U. Md Shah, “Physical, thermal and tensile behaviour of 3D printed kenaf/PLA to suggest its usability for ankle–foot orthosis–a preliminary study,” Rapid Prototyping Journal, vol. 28, no. 8, pp. 1573–1588, 2022.
M. J. Jweeg, H. Hamzah, M. Al-Waily, and M. A. Al-Shammari, “A Finite Element Simulation of Nano Effects on Stress Distribution in a Below Knee Prosthetic,” in IOP Conference Series: Materials Science and Engineering, vol. 1067, no. 1, IOP Publishing, 2021, p. 012141.
M. Zakaulla and S. Kesarmadu Siddalingappa, “Prediction of mechanical properties for polyetheretherketone composite reinforced with graphene and titanium powder using artificial neural network,” Materials Today: Proceedings, vol. 49, pp. 1268–1274, 2022.
F. T. Al-Maliky, J. S. Chiad, “Study and analysis the flexion moment in active and passive knee prosthesis using back propagation neural network predictive,” Journal of the Brazilian Society of Mechanical Sciences and Engineering, vol. 44, no. 11, 2022.
M. S. A.-D. Tahir, S. S. Hassan, and J. S. Chiad, “Kinematic analysis for passive multi-axes ankle joint,” Pollack Periodica, vol. 17, no. 2, pp. 36–41, 2022.
H. C. Nanotubes, “Nanomaterials Safety Considerations,” 2015.
M. Al-Waily, A. Deli, A. Al-Mawash, and Z. Ali, “Effect of Natural Sisal Fiber Reinforcement on the Composite Plate Buckling Behavior,” International Journal of Mechanical & Mechatronics Engineering (IJMME-IJENS), vol. 17, no. 1, 2017.
A. H. Jeryo, J. S. Chiad, and W. S. Abbod, “Boosting mechanical properties of Orthoses - foot ankle by adding carbon Nanotube particles,” Materials Science Forum, vol. 1039 MSF, pp. 518–536, 2021.
J. Chiad, “Design, Analysis and Optimization of the Knee-Ankle-Foot Orthosis,” Gulf University Journal for Engineering and Computer Engineering, vol. 4, no. 1, 2012.
J. Chiad, M. Al-Waily, and M. Al-Shammari, “Buckling Investigation of Isotropic Composite Plate Reinforced by Different Types of Powders,” International Journal of Mechanical Engineering and Technology (IJMET), vol. 9, no. 9, pp. 305–317, 2018.
American Society for Testing and Materials information, “Handing series 2000.”
Downloads
Published
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
The authors retain the copyright of their manuscript by submitting the work to this journal, and all open access articles are distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC-BY-NC 4.0), which permits use for any non-commercial purpose, distribution, and reproduction in any medium, provided that the original work is properly cited.
