×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this research, polymer polymethyl methacrylate PMMA composite with nano ceramic Zr and HAp material were used to manufacture one part of the implant system (femoral ball head of hip implant). Three set of hybrid materials were fabricated and tested for this study; the first mixtures which contains 100% (PMMA), the second mixtures which contains (90% (PMMA) + 8% (Zr) + 2% (HAp)), and the third mixtures which contains (80% (PMMA) + 18% (Zr) + 2% (HAp)) were investigated. The mechanical properties for these mixtures increased with the increasing of nano ceramic concentration (Zr and HAp) composite material in the polymer compared to pure polymer PMMA sample. However, an increase in the concentration of Zr from 8% to 18% content cause a considerable decrease of the hardness where a drop of homogeneity in Zr- matrix PMMA contact occurred, V Hardness value are (68 ,80 and 70) Kg.mm for three mixture respectively. The wear test was in agreement with results of the hardness test. The weight loss of the above samples of the wear test were (0.041, 0.035 and 0.037) respectively. According to mechanical properties, the best sample contains (90% (PMMA) + 8% (Zr) + 2% (HAp)). The Scanning electron microscopy resolute showed the particles forming semi-continuous network along grain boundaries polymer for second sample mixtures containing (90% (PMMA) + 8% (Zr) + 2% (HAp)), provides a low atomic packing and high energy. This will make the grain boundaries more reactive and strengthen mechanical performance. The Optical microscopy, Scanning electron microscopy and Xray spectroscopy analysis for In vitro test using SBF shows the growth of HAp layer with an increase in concentration of Ca and P elements formed on the surface of the second sample. This display of good results is a proof of the biocompatibility of the polymer sample.
The purpose of this study is to investigate the potential of biochar derived from Peganum harmala (Pgh) seeds as an adsorbent material for wastewater treatment. Biochar is a cost-efficient, ecologically friendly, and effective bio-sorbent for a wide range of pollutants in wastewater. Researchers are investigating the production of biochar from novel biomass sources. Phosphoric acid (H3PO4) was utilized in a chemical activation technique to produce biochar at various concentrations (20%, 30%, and 40%). The pyrolysis process lasted three hours at 600°C in a tube furnace with an inert nitrogen gas atmosphere. Elemental analysis, Brunauer-Emmett-Teller (BET) nitrogen adsorption, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), The biochar was characterized using several techniques, including elemental analysis, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) nitrogen adsorption, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The findings demonstrate the significant potential of Pgh seed-derived biochar as an inexpensive and ecologically acceptable sorbent material. A large surface area (691.58 m2g−1) was achieved at 600◦C for three hours with 40% H3PO4 activation.
Zinc oxide nano particles is one of the best choices for ultraviolet protection due to its special properties. In this research, the UV-protection ability of sol gel-derived thin ZnO films on cotton fabrics was investigated. Various polymers have been used as adhesives to bind the nano-oxide with the surface of the treated fabric. Scanning electron microscopy and UV spectroscopy were carried out to study the properties of the treated fabrics. The results showed that the diameters of the synthesis zinc oxide particles - (68.81, 41.76 and 44.6 nm) with (PVA, PVP and CMC) respectively- were of the nanostructure, and the smallest diameter of the particles was produced with polyvinylpyrrolidone as adhesive. Using a spectrophotometer showed a decrease in the transmittance of the studied samples compared with the raw untreated sample of about 23%.
The microstructural analysis and electrochemical measurements tests were used to investigate the behaviors of (TiO2) and (HAp)-coated Ti-6Al-7Nb alloy in the SBF solution .By using RF sputtering, a thin TiO2 layer coated the substrate, while a thick layer of HAp coated the outer side of surface. The generated middle layer consist of the composite of TiO2 and HAp which is by AFM characterized as uniformly distributed coating system with nano size. The images of the scan electron microscopy (SEM) shows that there is no any cracking observed in the outer layer of tested samples due to the use of thin film TiO2 as mid lead to reduce the difference in the thermal expansion between the HAp material and Ti-6Al-7Nb substrate .The HAp upper layer significantly improve the bioactivity of the Ti-6Al-7Nb alloy. In this study, the bonding strength and the corrosion resistance was improved by using thin layer of TiO2. From electrochemical impedance spectroscopy (EIS) study Bod plot, the composite layer of TiO2 and HAp was suggested by the capacitive act as barrier layer coated substrate and prevent the relays of the ion from metallic. The results shows the values of Rox (309.2 k? cm2)are greater than for Rct(19.2 k? cm2), by assumes the presence oxide film increases for coated substrate are greater than that of uncoated, which is a result of the presence of coated film that improve the corrosion resistance of the sample.
The Electrodeposition process has been used to prepare Nickel-Tungsten alloys on low carbon steel substrate by using ammonical citrate bath. The influence of deposition condition by variation of current density (0.04-0.2 A/cm2) and solution temperature (60-70 °C), on the microstructure was studied. The optical microscope and the scanning electron microscopy (SEM) were used to study the morphology of the deposit while the energy dispersive spectroscopy (EDS) was used to approximate the composition, in addition to X-Ray diffraction examination. The results show that the current efficiency has the major influence on the tungsten content in the alloys due to the formation of ternary complex which reflected into the properties of the deposit._x000D_ Keywords:
In this research, we successfully obtained Ni/SiC micro-composite coatings with various contents of SiC particles of particle size(10 ?m), by using electrodeposition method from nickel watts bath in which the SiC particles suspend. The effects of the current density, temperature, and particle loading(PL) of SiC particles in the electrolyte on the morphology, texture, and vol% of SiC in deposit were investigated. The morphological and structural analysis show uniform distribution of SiC particles within the composite coatings. It was found that the depositing conditions affect the microstructure of deposited nickel and the SiC vol% in deposit. Furthermore, the vol% of SiC increases in deposit by increasing the particle loading(PL) in the bath, while decreased by increasing the current density. Also the higher values of SiC vol% were obtained at temperature (50°C).
Strengthening elastomers by the Nano-fillers, for example, Graphite subordinates, have high embellishments on their attributes. In the present work, Graphene Oxide (GO) nano-sheets have scattered in huge rubbers was Nitrile Butadiene Rubber (NBR). Enhancement the vulcanization procedure on (GO/NBR) nano-composite elastic was performed by arrangement blending strategy and rumination blending method. Scattering of GO into NBR was homogenous, where affirmed by Scanning Electron Microscopy (SEM) and X-beam Diffraction (XRD) test. Breaking down the useful gatherings by Fourier-Transformed Infrared Spectrophotometry (FTIR) has been explored as well. Diverse stacking wt% of GO inside NBR has clear impacts on the rigidity and flexibility conduct of the nano-composite. Impact of GO on the electrical conductivity and persuasive properties of GO/NBR nano-composite elastic portrayed too. The GO presence has upgraded the crosslinking trademark in GO/NBR nano-composite elastic and enhanced its properties.
In the present study, magnesium-based composites reinforced with different volume fractions (3, 5, 10, and 15) vol.% of micro sized Al2O3 particulates were fabricated by powder metallurgy technique which involves mixed, compacted and sintered. Powders were mixed by ball milling (without balls) for 6 hours at rotation speed 60 rpm. Then powder was compacted at 550 MPa and sintered at 530?C for 2 hours. Microstructures of sintered composites have been investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD) energy dispersive. SEM image of sinter samples exhibit good bonding between the magnesium matrix and the alumina. The microhardness and wear resistance of micro composites has been improved significantly compared to that of pure magnesium. Highest value of microhardness is 97 HV at the volume fraction of 10 vol.% Al2O3.