×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThe breakage rate of liquid drops in the dispersed phase is a key way to improve the heat and mass transfer between the continuous/dispersed phases. This work includes a review of experimental results of liquid drop breakage in an agitated tank. The study highlighted the experimental conditions that were investigated as well as the important findings about the impact of operating conditions on some breakup parameters. The conflicts and discrepancies in the findings of those studies were identified and analyzed. The review found that many experimental parameters affect the drop breakage rate. The breakage probability (BP), number of fragments, and breakage time (BT) are direct functions of power input.
The hydrodynamics of stirred tanks and bubble breakup are crucial in gas-liquid flows, yet this system has not been well characterized for different operating conditions. In this work, the numerical method was used to investigate the hydrodynamics of six- flat blades impeller (Rushton turbine) and the results were employed to understand the bubble breakup behavior in the stirred tank. Simulation results of predicted flow pattern, power number, and the distribution of turbulence energy generated were performed with COMSOL Multiphysics. Numerical results showed good agreement with the experimental literature. The effect of rotational speed on bubble breakup behavior, such as breakage probability, the average number of daughter bubbles, and the breakage time was investigated using the high-speed imaging method. The main finding is that the breakage process occurs in the high energy area of high turbulence intensity, which is located within a distance equal to the blade width of a radius of (15-35 mm). The breakage probability (Bp) was found to be increased by 12.61 percent for a mother bubble of 4 mm at 340 rpm, with an average fragmentation of up to 22 fragments. Furthermore, the bubble breakage time was found to decrease with increasing impeller rotational speed, with an average value of 19.8 ms.
The purpose of this study is to investigate the potential of biochar derived from Peganum harmala (Pgh) seeds as an adsorbent material for wastewater treatment. Biochar is a cost-efficient, ecologically friendly, and effective bio-sorbent for a wide range of pollutants in wastewater. Researchers are investigating the production of biochar from novel biomass sources. Phosphoric acid (H3PO4) was utilized in a chemical activation technique to produce biochar at various concentrations (20%, 30%, and 40%). The pyrolysis process lasted three hours at 600°C in a tube furnace with an inert nitrogen gas atmosphere. Elemental analysis, Brunauer-Emmett-Teller (BET) nitrogen adsorption, scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), The biochar was characterized using several techniques, including elemental analysis, X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), Brunauer-Emmett-Teller (BET) nitrogen adsorption, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDX). The findings demonstrate the significant potential of Pgh seed-derived biochar as an inexpensive and ecologically acceptable sorbent material. A large surface area (691.58 m2g−1) was achieved at 600◦C for three hours with 40% H3PO4 activation.
Dyes are important chemicals in industrial uses; however, they are considered hazardous materials because they accompany sewage and are one of the causes of serious diseases such as cancer if not treated properly. The aim of this study is to specify the effect of dyes on the environment and human health and to remove them from water using the photochemical agent (polyoxometalate). By studying two types of Phosphotungstic acid (PTA) and phosphomolybdic acid (PMA) due to the good possibility of loading these acids on other materials using mixing and precipitation ways and without the need for high temperatures, as they are prepared at room temperature. They are also solid materials that are easy to separate, quickly dissolve in water, non-toxic, and do not release dangerous gases, which led to the need to use them in removing dyes, as they gave high efficiency. The research explains a comprehensive review of the use of PTA and PMA acid in Visible light-enhanced degradation of organic dye pollutants for three dyes: methylene blue, methyl orange and chromium B. Previous research is reviewed, with special emphasis on the performance of the photocatalyst, conditions that increase its efficiency, and the proposed mechanisms for the combined photocatalysts of PTA and PMA acids in developing the photocatalytic process. Finally, recent findings in this area are discussed, and possible future research continuations are suggested.
The oil industry has a direct impact on the economic feasibility of other sectors and is considered to be the most important energy source used to turn the wheels of other industries. Therefore, it was necessary to pay attention and continuously develop this industry, to find the best modern techniques for designing, pre-commissioning and controlling process, to improve efficiency, preserve energy and achieve the highest production of costly components with the highest purity of the product. This study aims to provide a literary analysis of the stages of development and progress of the dynamics and control of the petroleum industry, in particular the distillation column, because it is multivariable with high interaction between control cycles, nonlinear behaviour and large gains. Control processes have undergone many developments and modernizations to achieve the best results. Various control methods have been used, ranging from simple proportional-integral-derivative controller (PID) to advanced control strategies such as model predictive control (MPC), multivariate model predictive control (MMPC), fuzzy logic control (FLC), quadratic dynamic matrix control (QDMC), artificial neural network control (ANN) and other advanced control techniques. The authors concluded from the review that the advanced control strategies superior than the conventional methods.
Catalytic isomerization is a process used to increase the octane number of light naphtha fraction and thus aids in extending the life of automobile engines. Researchers are still working to prepare more effective and less expensive isomerization catalysts to replace the costly previous catalysts. Ongoing challenges in this field seek to design highly active isomerization catalysts operated under moderate conditions while keeping high branched-isomer selectivity. Heteropolyacids (HPA) have been presented as the most capable substitutes to fulfill the requirements. They are considered bifunctional catalysts that perform dehydrogenation /isomerization followed by hydrogenation because of their firm acidity and redox properties. Some catalytic-isomerization studies were started utilizing HPA in combination with platinum, which significantly improves the selectivity and stability. Thus, HPA-based bifunctional catalysts can provide enough acid and hydrogenation–dehydrogenation sites sufficiently. However, the most ongoing challenge in this field is the poor thermal stability of HPAs, which limits their use at higher temperatures for vapour-phase reactions. This review aims to highlight the recent progress in catalytic isomerization of alkanes using heteropolyacids supported on different carriers, with and without noble metals.
The separation of water from crude oil emulsions is a critical and complex challenge in petroleum production and processing. Water-in-oil (W/O) emulsions increase viscosity, pose corrosion risks, reduce refining efficiency, and raise significant environmental concerns. Traditional separation methods often struggle with stable emulsions containing small droplets due to limitations in cost, environmental impact, and effectiveness. Electro-coalescence demulsification has emerged as a promising technique that applies electric fields to enhance droplet coalescence, facilitating efficient water removal. This comprehensive review examines the influence of electrode geometry on electro-coalescence systems in depth, synthesizes key findings from numerous studies, and provides a detailed analysis of electrode spacing calculations, critical conditions for effective demulsification, and optimal operational parameters. By exploring these aspects comprehensively, the review offers insights into how electrode design affects demulsification efficiency, guiding future advancements in crude oil processing and contributing to more sustainable practices in the petroleum industry.
The impact of flow velocity (0-900 rpm) on the corrosion rate of carbon steel in a wide range of sulfuric acid concentrations (0-90% in H2O) at 30 °C and 1 h was studied and discussed. In addition, the efficiency of corrosion inhibitor (dimethyl disulfide, DMD) was evaluated in hardest corrosion conditions for the range of velocity investigated. The results revealed that increasing the flow velocity of H2SO4 solution, increases the corrosion rate depending on the acid concentration. When the flow velocity is increased of H2SO4 solution, the corrosion potential was shifted to more negative. The DMD inhibitors showed significant inhibition efficiency at high velocities, where the highest percentage of inhibitor efficiency reached 98% at 900 rpm.
Industrial activities significantly affect the environment by releasing many organic pollutants, including industrial dyes, phenols and antibiotics, which produce wastewater. Effective removal of these substances from wastewater has appeared as a noticeable research field owing to its environmental significance. Exorbitant operational expenses and the potential generation of supplementary pollutants load conventional techniques like adsorption, membrane separation, and coagulation. Semiconductor-based photocatalysis has effectively degraded organic contaminants into less toxic or biodegradable compounds. The construction of robust visible-light-sensitive photocatalytic hybrids for environmental decontamination is an inspiring task for researchers. The exceptional photocatalytic performance of silver halides (AgX, where X is I, Cl, and Br) has recently attracted significant consideration as photocatalysts. Moreover, the combination of silver halides with other photo-active semiconductors to create efficient visible-light-driven photocatalyst heterojunctions has significantly promoted the broader application of the photocatalysis process with enhanced efficiency. Ag-silver halides/semiconductors heterojunctions have developed as crucial components in efficient composites for photocatalysis through surface plasmonic actions, helping with visible light absorption. The current study overviews the most recent Ag and silver halide-based composite photocatalysts. Additionally, it provides an essential understanding of their promoted photocatalytic performances and their main applications in organic pollutant degradation. Moreover, the photocatalytic mechanisms and environmental applications of AgI and composites were discussed.
The goal of the study is to predict the Man in the Middle attack in the packets of Wireshark program by using Support Vector Machines (SVM).In the time of using the internet, it has become a tool targeted by attackers and hackers; it is a serious threat to the devices. A uniqueness of an attack that appears in multiple identities for legitimate agencies. It is very necessary to know the behavior attack and predict the possible actions of an attacker. In this research a detection of Man in the Middle attack by monitoring the Wireshark program and recording any changes can be recognized in packet information. The classification of packets is divided into two categories (normal and abnormal). The proposed model is designed in many stages: loading data, processing data, training data, and testing data. The detection of SVM based on abnormal network packet through movement packets in the Wireshark program that needs to deal with current packets to recognize a new attack that one does not have prior knowledge of its detection, and there is a need for an intelligent way to separate network packets that represent normal. The proposed approach achieved an accuracy of 97.34% in detecting attacks. The results show that the proposed model effectively visualizes attacker behavior from data that represents abnormal network attackers. Research achieves successful accuracy in predicting abnormalities.
The purpose of this research is to manufacture and test adjustable sockets for below-knee amputation. This article studies using the pnuematic–pads for adjustable sockets. The manufacturing of an adjustable socket with pneumatic pads goes through several stages: In the theoretical design of the adjustable socket, the suggested materials were studied for the pneumatic pads, tubes, and pneumatic pump which should be suitable for the suggested application. In the experimental work, using composite materials for manufacturing the socket consisting of perlon and resin to achieve the rigid shape and required flexibility for the prosthetic user with the pneumatic pads. After assembling the adjustable socket parts, the pneumatic pads, the pump and the tubes, the socket were tested for several times on the patient. In the last stage, the pressure between the socket and the residual limb was measured using F-socket, and it was found that the results were: anterior (160kPa), lateral (167kPa), posterior (153kPa) and medial (348kPa). By comparing these results with what was previously studied, the pressure between the socket and the residual limb is within the acceptable range. The design provides good suspension and more adaptability to the change in stump volume. A posative feedback was given by the patient who used the prosthetic patient for several days as a trial to measure its safety and comfortablty.
Basrah is the richest town and the economic capital of Iraq. It suffers from lack of drinking water. This project is a dream to supply drinking water to Basrah citizens within WHO standards. Water should pass sedimentation and filtration stages before interring reverse osmosis unit. The design is carried out using lewaplus2 software. Several parameters should be selected in the design step membrane type, number of stages, number per element in each stage, and the recovery percentage. An optimization is carried out using Minitab ver. 18 for the acceptable limit of TDS and minimum cost and it was found that the optimum conditions were 52% for first stage, the numbers of vessels are 20 for both the first and second stage. In addition, results showed that the pressure and the total dissolved solid increase with increasing the recovery while parameters like the feed flow rate per vessel, the power, and the cost are decreasing with the recovery. Mathematical model described the cost was conducted and statistical study was also done to ensure the results.
The presence of heavy metal pollutants in refinery effluent significantly impacts the corrosion rate of carbon steel. The focus of this research is to analyze the impact of various inorganic pollutants, including copper, vanadium, nickel, and chromium ions, on the corrosion of carbon steel across different solutions. After conducting a thorough examination of various operating conditions, including pollutant concentration (ranging from 300-3000 ppm), temperature (30-60? C), and flow velocity (0-800 rpm). Our research shows that copper ions have the highest corrosion rate, with vanadium ions being a close second. Conversely, nickel and chromium had the most negligible impact on corrosion rate and, in some instances, even exhibited corrosion inhibition effects. It was also observed that an increase in flow velocity and temperature significantly amplified the corrosion rate of the metal ions investigated.
In this paper, the efficiency of six different types of corrosion inhibitors used in Basrah drinking water tanks was assessed using a potentiostatic test method. The mechanism of adsorption of silicate and phosphate inhibitors in AISI 316 stainless steel surfaces and the effects of different water components in inhibitors are discussed in detail. The values of corrosion rate obtained from the Potentiostatic test showed that the protection against corrosion in the presence of inhibitors is better compared to the case of absence of inhibitors. The results of the six types of corrosion inhibitors tested showed that the inhibitory efficacy is higher below the temperatures 45oC, but when raise the temperature above 45oC the inhibitory efficiency becomes to decrease. Also, the test results indicated that the corrosion inhibitor involves silicate products provided more inhibited efficiency compared to the phosphate inhibitor alone or used the combined silicate/phosphate corrosion inhibitor. The inspection of the surface of the tested samples using optical methods shows that the pitting corrosion is demonstrated on the specimen surfaces after testing with or without inhibitors.