×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this paper, the efficiency of six different types of corrosion inhibitors used in Basrah drinking water tanks was assessed using a potentiostatic test method. The mechanism of adsorption of silicate and phosphate inhibitors in AISI 316 stainless steel surfaces and the effects of different water components in inhibitors are discussed in detail. The values of corrosion rate obtained from the Potentiostatic test showed that the protection against corrosion in the presence of inhibitors is better compared to the case of absence of inhibitors. The results of the six types of corrosion inhibitors tested showed that the inhibitory efficacy is higher below the temperatures 45oC, but when raise the temperature above 45oC the inhibitory efficiency becomes to decrease. Also, the test results indicated that the corrosion inhibitor involves silicate products provided more inhibited efficiency compared to the phosphate inhibitor alone or used the combined silicate/phosphate corrosion inhibitor. The inspection of the surface of the tested samples using optical methods shows that the pitting corrosion is demonstrated on the specimen surfaces after testing with or without inhibitors.
The current study presents the plasma cutting process of 2 mm thickness of AISI 1020 carbon steel. The experiment conducted by taking into the account the effect of two process parameters, including cutting current of 15 and 20 A with cutting speed in range of 500 - 4000 mm/min, on the kerf formation, microstructure and microhardness.The results showed that at low cutting current of 15 A the melting occurred at the workpiece surface without cutting action. Increase the current to 20 A led to full penetration of the workpiece material at low and high cutting speed, with kerf width between 1.26 mm and 1.1 mm for cutting speed of 500 mm/ min and 4000 mm/ min, respectively. The plasma arc cutting speed has a high impact on the heat-affected zone HAZ and microstructure development with coarse grains at the HAZ at low cutting speed of 500 mm/min and constant current of 20A, increase the plasma cutting speed led to decreasing the grain size. The microstructure of the HAZ exhibited a presence of perlite and ferrite with some martensite structure. The highest microhardness of the HAZ of 220.8 HV was found in the sample processed at 20 A current and high cutting speed of 4000 mm/ min. However, the minimum microhardness of the HAZ of 156.7 HV was found in the sample processed at 20 A current and low cutting speed of 500 mm/ min.
In the present work the effect of Corrosion & Scale Inhibitor was evaluated by using of the commercial product (Kurita S2050) that mainly containing of (Na2HPO4) sodium phosphate as corrosion inhibitor and (C6H11NaO7) sodium glocunate as scale inhibitor & dispersant. The dosing rate of this chemical was controlled according to the treatment system depend mainly on the monitoring of LI & RI indexes for (30) days treatment in the cooling tower unit of Al-Dora Oil refinery-Baghdad. The corrosion rate and the corrosion inhibitors efficiency were calculated by measurement of weight loss in standard test coupon (AISI 1010). After 30 day of the Field Test, the result show that the treatment program performance was effective in the corrosion & scale inhibition through an acceptable corrosion rate less than 0.018 in gmd. Also the result of corrosion rate was analyzed statistically by using of (ANN) to formulate a prediction equation to corrosion rate identification.
Desired mechanical properties like microstructure, micro hardness and wear resistance are the key parameters for which low carbon steel (AISI 1006) are widely selected. Surface heat treatment applied to improve these properties; traditionally surface heat treatments like induction hardening, in recent time’s laser surface hardening. In this work, thermochemical treatment (liquid nitriding) by using mixture from 61% NaCN, 15% K2CO3 and 24% KCL and followed by Nd:YAG laser surface treatment was done . The laser parameter were energy (0.89, 2, 4 and 9) J, spot diameter (0.790 ,0.33, 0.283 and 0.224) mm, pulses duration (1, 2.33, 4.47 and 9.87) ms with fix wavelength 1604nm. Laser surface treatment cycle was melting the layer surface, holding and rapid cooling in air medium. Optical microscopy (OM) and scanning electron microscope (SEM) has been used to study the microstructures and cross-sectional of molted and heat affected zones respectively. The wear test was done to measure the wear rate by using pin -on-disk principles were satisfied. The result shown that increasing in laser energy effects to increase in the area of melted and heat affected zones of nitriding steel. Also increasing in laser energy led to increase micro hardness about 61%, while wear rate decrease about 40 % and increased depth of molted zone.
Super-hydrophobic is the tendency of a surface to spit out water droplets. Only a surface with high apparent contact angle (>1500), low contact angle hysteresis (<100), low sliding angle (<50), and strong Cassie model state stability is considered a super-hydrophobic surface. In an attempt to create highly hydrophobic synthetic surfaces suitable for a range of uses, attempts have been made to mimic the super-hydrophobicity found in natural materials (such as lotus leaves). Due to its wide range of applications including waterproof, anti-fog, anti-ice and anti-corrosion surface, the laser processing process achieved the use of process parameters which had a significant impact on the roughness factor. High roughness factor F. At constant values of p = 3 mW and ω = 10 μm, at scanning speeds of 6000 mm/s.