Articles in This Issue
Abstract
This paper focused on evaluating the effect of aggregate gradation and polymer modification on indirect tensile strength (ITS) and the static stiffness for hot asphalt mixtures. In particular, data from ITS tests have been processed to obtain stiffness measurements through the application of Hondros theory. The results showed that fine mixtures had a better tensile strength by 26.3% than the coarse mixtures. The effect of compaction also was examined, the results showed that samples compacted with the Superpave gyratory compactor (SGC) had an enhancement in ITS by 36.58 and 23.1% in comparison with Marshall and roller compactor respectively. Polymer modifiers were used to estimate their effect on tensile strength, adding 4, 6, and 8% of Styrene-Butadiene-Styrene (SBS), which can rise the ITS by 3.2,6.14 and 13.3% of the non-modified asphalt mixture. Furthermore, using 4, 6, and 8 percent of SBS could increase static stiffness by 53.9, 209.6, and 302.4% respectively for roller compacted fine mixes and 58, 220, and 379.3% for SGC compacted mixes. Furthermore, SBS raised the stiffness modulus by 52.3, 188, and 295% for Marshall compacted mixes. Using hybrid modifier can improve the stiffness of the asphalt mixture. However, The results indicate that using 1, 2 and 3% polyvinyl chloride (PVC) can magnify the stiffness of mixtures by 41.2, 199.8% and 262.6 for roller compacted mixtures and 133.4, 212.1 and 354% for SGC compacted mixtures, whereas there is a stringent increasing by 133.4, 189.2 and 354% for Marshall compacted mixes. Otherwise, polymer-modification can decrease the fracturing index for coarse and fine mixtures.
Abstract
In this paper, the H-infinity Sliding Mode Control (HSMC) is designed to produce a new dynamic output feedback controller for trajectory tracking of the nonlinear human swing leg system. The human swing leg system represents the support of human leg or the humanoid robot leg which is usually modeled as a double pendulum. The thigh and shank of a human leg is represented by two pendulum links and the hip joint will connect the upper body to the thigh and the knee joint will connect the thigh to the shank. The external torques (servo motors) are applied at the hip and knee joints to move the muscles of thigh and shank. The results show that the HSMC can robustly stabilize the system and achieve a desirable time response specification better than if only H-infinity or SMC is used. This controller achieves the following specifications: sec, for hip joint and sec, for knee joint.
Abstract
In this research, we investigate the nonlinear vibration of functionally graded carbon nanotubes (FG-CNTs) for simply supported sandwich cylindrical panels. The sandwich consisting of three layers formed of (FG-CNTs) and isotropic material as (CNT, ALMINUME, CNT). Mechanical properties of the sandwich media are acquired according to a re?ned rule of blend approach. The governing equations were derived using a first-order deformation theory (FOSDT). Four kinds of carbon nanotubes of sandwich cylindrical panels were analyzed. The volume fraction of CNTs is varied. The properties of nonlinear responses and free vibration are studied. The numerical approach employs the fourth-order Runge-Kutta and Galerkine procedure. Which conducted for the dynamic analysis of the panels to present the natural frequencies and non-linear dynamic response expression. The results show that; the natural frequencies and the nonlinear vibration amplitude decrease with the volume fraction and thickness ratio increase. The nonlinear vibration amplitude response increases when increasing the excitation force. The initial imperfection and the elastic foundation have a minor impact on the nonlinear vibration response of the panel. The Pasternak Foundation has a larger impact than the Winkler foundation. The structure formed of FG-CNT present an excellent choice for high-performance of engineering applications.
Abstract
Experiments were conducted to study the effect of quenching medium carbon steel in water-based MWCNTs nanofluids at 0.05 % wt. concentration quenchant, a large cylindrical sample with 46 mm diameter and 40 mm length made from medium carbon steel used with three K-type thermocouples with a diameter of 1.5 mm inserted in three locations for sample (center of the sample, mid-point between center and surface and 1 mm from the surface). A time-temperature reading data system was used to read temperature history during cooling stage.The same experiments were simulated using ANSYS Workbench with Thermal Transient Version 19, the cooling curves at three locations for the cylindrical steel sample calculated during quenching in MWCNTs nanofluids. Quench factor analysis was used to predict the hardness results from the calculated and measured cooling curves, and these results compared with the hardness test results conducted in the significant sample from the center to the surface. The results show excellent compatibility when compared between the hardness results from cooling curves, and it also shows a good agreement with the results of the hardness test, especially at the sample surface.
Abstract
The aim of this work is to investigate the effect of soil corrosion on the critical buckling load of circular columns made of 2014-T4 aluminum alloy. In this work, 24 specimens were used and buried in the soil for 120 days. The samples divided into two groups (12 columns with corrosion before shot penning (SP) and ultrasonic impact treatment (UIT), and 12 columns with corrosion after combined surface treatments (SP+UIT)). The experimental1results revealed1that the corrosion negatively1affects the mechanical properties1of the material, and the1reduction percentage (R%) for1ultimate tensile strength (UTS) and1yield strength (YS) was (1.95% and 4.57%) respectively. After combined surface treatments (SP+UIT) for the corroded columns, the ultimate1tensile strength (UTS) and yield1strength (YS) were improved with (2.42%, and 2.87%) respectively. Perry-Robertson, Rankine, and ANSYS were used to estimate the critical buckling load (Pcr) and compare it with the experimental results. Rankine and Perry's formulas have been achieved a good agreement with the experimental without and with (1.5) factor of safety respectively. While ANSYS gave satisfactory prediction with a safety factor of (2.2, and 2.7) and (1.9, and 2.7) for long and intermediate columns before and after (SP+UIP) respectively.
Abstract
This paper presents a dual wide-band band pass filter (DWB-BPF) by using two parallel, symmetrical micro-strip lines loaded by a centered resonator, consisting of a T- and a triangle-shaped geometry, attached at the lower and upper ends, respectively. The filter reveals good performance and both the passbands can be independently controlled by adjusting specific parts of the filter. The proposed BPF is simulated by using CST microwave studio package and the simulated result is verified experimentally with good agreement between the two results. The fabricated prototype BPF demonstrates two passbands located at 2.3 GHz and 6.35 GHz center frequencies with 39% and 23.6% of 3-dB fractional bandwidth (FBW), respectively and a good insertion and return losses. The designed BPF can be targeted for wireless local area network (WLAN), WIFI and satellite communication systems.
Abstract
The transportation cost problem of solid waste presents the biggest part of the budget allocated by municipalities for SWM. So, there is no comprehensive plan to address transport routes optimization problems in SWM that including the transfer of solid waste from transfer stations to final landfill sites. Therefore, the aim of the study finding a scientific method to solve the transportation problem of solid waste transport suitable Baghdad city that tries to find feasible solutions that ensure reducing total transport costs and leads to an effective solid waste management system. In this research, a new methodology has been developed to select the optimal transport routs of SWM in Baghdad city which involves determining the best-supposed scenario. the proposed methodology includes integration of Global Positioning System (GPS) technologies with Network Analysis model (NA). Therefore, this work provides an advanced framework of decision-makers for analysis and simulation of the optimal transport routs problem related to SWM. Applying these modeling tools to select the scenario that can provide economic benefits by minimizing travel time, travel distance and reduction of total transportation costs. The Results of work implementation show that all solutions that include current state S1 and suggested scenarios have been evaluated. The scenarios generated include (S2, S3) by applying the proposed technique for analyzed and identified the optimal routes. The solutions of scenario S2, specified with two landfill sites while scenarios S3 specified with four landfill sites. Finally, this work shows the Scenario S3 is the best scenario of the solution, that include applied GPS and Network Analysis for four landfill sites.
Abstract
Prosthetic is an artificial tool that replaces part of the human frame absent because of ailment, damage, or distortion. The current activities in Iraq draw interest to the upper limb discipline because of the growth in variety of amputees and. It is necessary to do extensive researches in this subject to help lessen the struggling of patients. This paper describes the design and development of low-cost prosthesis for people with transradial amputations. The presented design involves a hand with five fingers moving by means of a gear box mechanism. The design of this artificial hand allows five degrees of freedom(5DOF), one degree of freedom for each finger. The artificial hand works by an actuation system (6V) Polou motor with gear ratio equal to 50:1 due to its compactness and cheapness. The designed hand was manufactured by a 3D printing process using polylacticacid material (PLA). Some experimental were accomplished using the designed hand for gripping objects. Initially the EMG signal was recorded when the muscle contracted in one second, two seconds, three seconds. The synthetic hand was able to produce range of gesture and grasping moves separately just like the actual hand by using KNN classification which are complete hand Pinch, fist, and jack chuck. The simulation of the fingers movements was achieved using ANSYS software to analysis the movement (pinch, fist, and jack chuck), obtain bested of stress influencer at each finger, and maximum deformation at each movement.
Abstract
Gait analysis can be described as a field of biomechanical engineering dealing with the subject of human locomotion. This study aimed to identify the effect of Ilizarov on gait when the presence the above-knee prosthesis. The study was made on a 50-year-old male patient was underwent correction right tibia with Ilizarov fixation due to war accident in July 2012. Also, this accident led to trans-femoral amputation. Two-dimensional gait system of a synchronized 25 Hz camera with an AMTI force platform was use for measuring gait kinematics and kinetics data while walking at a self-selected speed. These data can be used as standard measures in pathology studies, as input to theoretical joint models, and as input to mechanical joint simulators treated with Ilizarov and prosthetics.
Abstract
Desired mechanical properties like microstructure, micro hardness and wear resistance are the key parameters for which low carbon steel (AISI 1006) are widely selected. Surface heat treatment applied to improve these properties; traditionally surface heat treatments like induction hardening, in recent time’s laser surface hardening. In this work, thermochemical treatment (liquid nitriding) by using mixture from 61% NaCN, 15% K2CO3 and 24% KCL and followed by Nd:YAG laser surface treatment was done . The laser parameter were energy (0.89, 2, 4 and 9) J, spot diameter (0.790 ,0.33, 0.283 and 0.224) mm, pulses duration (1, 2.33, 4.47 and 9.87) ms with fix wavelength 1604nm. Laser surface treatment cycle was melting the layer surface, holding and rapid cooling in air medium. Optical microscopy (OM) and scanning electron microscope (SEM) has been used to study the microstructures and cross-sectional of molted and heat affected zones respectively. The wear test was done to measure the wear rate by using pin -on-disk principles were satisfied. The result shown that increasing in laser energy effects to increase in the area of melted and heat affected zones of nitriding steel. Also increasing in laser energy led to increase micro hardness about 61%, while wear rate decrease about 40 % and increased depth of molted zone.
Abstract
Computed tomography (CT) imaging is an important diagnostic tool. CT imaging facilitates the internal rendering of a scanned object by measuring the attenuation of beams of X-ray radiation. CT employs a mathematical technique of image reconstruction; those techniques are classified as; analytical and iterative. The iterative reconstruction (IR) methods have been proven to be superior over the analytical methods, but due to their prolonged reconstruction time, those methods are excluded from routine use in clinical applications. In this paper the reconstruction time of an IR algorithm is minimized through the employment of an adaptive region growing segmentation method that focuses the image reconstruction process on a specified region, thus ignoring unwanted pixels that increase the computation time. This method is tested on the iterative algebraic reconstruction technique (ART) algorithm. Some phantom images are used in this paper to demonstrate the effects of the segmentation process. The simulation results are executed using MATLAB (version R2018b) programming language, and a computer system with the following specifications: CPU core i7 (2.40 GHz) for processing. Simulation results indicate that this method will reduce the reconstruction time of the iterative algorithms, and will enhance the quality of the reconstructed image.