Enhancement of Hot Mix Asphalt stability by utilizing Cement Kiln Dust and Styrene-Butadiene-Styrene Polymer
DOI:
https://doi.org/10.29194/NJES.26020124Keywords:
Hot Mix Asphalt, Cement Kiln Dust, ITS, Styrene-Butadiene-Styrene, StabilityAbstract
Utilization of additives can be an effective way to improve the durability and performance of HMA, making them more resistant to Moisture and deformation. Plus, they can reduce the need for maintenance and repairs, saving you time and money in the long run. In this study, CKD was used in place of limestone as a filler in the asphalt mixture in proportions of 0%, 25%, 50%, 75%, and 100%, and polymer SBS 4%by weight of asphalt. According to the findings, replacement-content CKD had the highest asphalt content. When the CKD is between 25% and 50%, Stability, Flow, and Indirect Tensile Strength are improved, while the density of the asphalt mixture decreases and the amount of air voids increases at higher ratios. While SBS leads to an increase in the hardness of the adhesives. As a consequence, the stability of the SBS-containing mixes resulted in higher values than the control and additive-containing mixtures (CKD), as well as a decrease in the number of air voids. According to the results, CKD should not constitute more than half of the filler weight in the asphalt mixture.
Downloads
References
A. H. Abed and Z. I. Qassim, “Impact of Gradation and Modifier on Moisture Susceptibility of Iraqi Hot-Mix Asphalt,” 2015, no. October.
K. H. I. Al Helo, Z. I. Qasim, and M. A. Abdulhussein, “Effect of laboratory aging on moisture susceptibility of polymer-modified bituminous mixtures,” IOP Conf. Ser. Mater. Sci. Eng., vol. 737, no. 1, 2020, doi: 10.1088/1757-899X/737/1/012131.
S. Sobhi, A. Yousefi, and A. Behnood, “The effects of Gilsonite and Sasobit on the mechanical properties and durability of asphalt mixtures,” Constr. Build. Mater., vol. 238, p. 117676, 2020, doi: 10.1016/j.conbuildmat.2019.117676.
I. Amin, S. M. El-Badawy, T. Breakah, and M. H. Z. Ibrahim, “Laboratory evaluation of asphalt binder modified with carbon nanotubes for Egyptian climate,” Constr. Build. Mater., vol. 121, pp. 361–372, 2016, doi: 10.1016/j.conbuildmat.2016.05.168.
K. D. Stuart, “Moisture damage in asphalt mixtures-a state-of-the-art report,” 1990.
R. Roque, B. Birgisson, C. Drakos, and G. Sholar, “Guidelines for use of modified binders,” 2005.
M. S. Cortizo, D. O. Larsen, H. Bianchetto, and J. L. Alessandrini, “Effect of the thermal degradation of SBS copolymers during the ageing of modified asphalts,” Polym. Degrad. Stab., vol. 86, no. 2, pp. 275–282, 2004.
S. Tayfur, H. Ozen, and A. Aksoy, “Investigation of rutting performance of asphalt mixtures containing polymer modifiers,” Constr. Build. Mater., vol. 21, no. 2, pp. 328–337, 2007.
Z. Vlachovicova, C. Wekumbura, J. Stastna, and L. Zanzotto, “Creep characteristics of asphalt modified by radial styrene–butadiene–styrene copolymer,” Constr. Build. Mater., vol. 21, no. 3, pp. 567–577, 2007.
U. Isacsson and H. Zeng, “Relationships between bitumen chemistry and low temperature behaviour of asphalt,” Constr. Build. Mater., vol. 11, no. 2, pp. 83–91, 1997.
M. C. Won and M. K. Ho, “Effect of antistrip additives on the properties of polymer-modified asphalt binders and mixtures,” Transp. Res. Rec., no. 1436, 1994.
S. Shuler and D. I. Hanson, “Improving durability of open-graded friction courses,” Transp. Res. Rec., vol. 1259, pp. 35–41, 1990.
A. A. Elbaz, A. M. Aboulfotoh, A. M. Dohdoh, and A. M. Wahba, “Review of beneficial uses of cement kiln dust (CKD), fly ash (FA) and their mixture,” J. Mater. Environ. Sci, vol. 10, no. 11, pp. 1062–1073, 2019.
2003) (SCRB R/9, General Specifications for Roads and Bridges. 2003.
ASTM D6927, “Standard Test Method for Marshall Stability and Flow of Asphalt Mixtures, ASTM International, West Conshohocken, PA.,” Astm D6927, vol. i, pp. 1–7, 2015, doi: 10.1520/D6927-15.2.
ASTM D1559, “Resistence to Plastic Flow of Bituminous Mixtures Using Marshall Apparatus,” Annual Book of ASTM Standards. pp. 1–5, 1989.
ASTM-D2726, “Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive,” Am. Soc. Test. Mater. ASTM Stand., vol. 04, pp. 4–7, 2000.
ASTM D-2041-03, “Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures,” ASTM Int., pp. 1–7, 2003, [Online]. Available: www.astm.org,.
ASTM D-3203-05, “Percent Air Voids in Compacted Dense and Open Asphalt Mixtures,” Aashto, pp. 6–7, 2015.
M. A. Abed and A. H. Abed, “Effect of Hybrid Modification and Type of Compaction on the Cracking Properties of Asphalt Concrete,” Al-Nahrain J. Eng. Sci., vol. 23, no. 2 SE-Articles, pp. 106–116, Sep. 2020, doi: 10.29194/NJES.23020106.
ASTM D4867, “Standard Test Method for Effect of Moisture on Asphalt Concrete Paving Mixtures,” ASTM Int., pp. 1–5, 2014.
A. D-6931-12, “Standard Test Method for Indirect Tensile ( IDT ) Strength of Bituminous Mixtures 1,” pp. 4–8, 2012, doi: 10.1520/D6931-12.2.
Downloads
Published
Issue
Section
License
Copyright (c) 2023 Hiader F. Abbas, Alaa H. Abed
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
The authors retain the copyright of their manuscript by submitting the work to this journal, and all open access articles are distributed under the terms of the Creative Commons Attribution-NonCommercial 4.0 International (CC-BY-NC 4.0), which permits use for any non-commercial purpose, distribution, and reproduction in any medium, provided that the original work is properly cited.
How to Cite
