×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis paper studies the effect of different design spectral response acceleration parameters as suggested by the uniform building code (UBC), unified facilities criteria (UFC), and Iraqi seismic code(1997) (ISC 97) on the seismic response of reinforced concrete multi-story framed building located in Baghdad city, Iraq. These parameters are: (a) spectral response accelerations Ss, at short periods, and S1 at a 1-second period in accordance with international building code (IBC), (b) seismic zone factor (Z) according to UBC, (c) Seismic hazard zoning coefficient (Z) according to ISC 97. In this paper, first, the elastic seismic responses for significant modes of vibration for chosen building under design response spectrum that obtained from the above mentioned codes are calculated, and then a comparison was made among different design spectral response acceleration parameters. The intent of this study is to review the seismic provisions of the current edition of Iraqi seismic code (1997) to determine whether it provides an equivalent level of safety to that contained in other international codes. Design base shears, lateral seismic forces, inter story drifts, response spectrum modal, effective seismic modification, floors acceleration and story shears are comparatively presented.
This paper aims to assess the structures' seismic response with a system of Single-degree-of-freedom exposed to near-fault earthquakes, taking into account the effect of pulse period, shear wave velocity (VS30), and fault mechanism. Strong ground motion data were taken for different events in different places around the world and the prism software program is used for the analysis of seismic response for structures recognized as single-degree-of-freedom systems. Results show that the ground motion with a higher value of (VS30) provides an acceleration response higher than that of the lower value of (VS30). However, the findings revealed that the peak displacement requirements are observed in a nearby of the pulse period limits. In addition, it is noticed that there is an obvious increase in spectrum demand with longer pulse periods. Finally, results show at short vibration periods (T? 0.6sec) for both types (strike slip and dip slip) comparable results while an increment is observed in the results of the strike-slip for vibration periods more than (0.6sec) of the acceleration response spectrum. Nonetheless, for the velocity response spectrum dip-slip continuous in flocculating with a significant increase.
In this work, the vibrations in the rotor-bearing system are studied experimentally and theoretically using ANSYS Workbench 2020 R1 software to compute the natural frequencies and mode shapes. In the experimental part, the LABVIEW software was used to examine the signal of the frequency domain values obtained from the accelerometer sensors, based on Fast Fourier Transform (FFT) technology and dynamic response spectrum. in the theoretical part, the natural frequencies are determined based on the finite element method for analyzing the system and knowing its behavior and vibration response level. The results showed that the level of vibration becomes higher at high rotational speeds, and it becomes large when the distances between the bearings are large, according to the bearing position and type used in the system. in this work can be concluded, the system is usually affected by the dynamic response around it and is difficult to separate from it, and the vibrations in the system can be controlled by adding an external damping source, which gives the system more stable. A system operating at high speeds can give a large vibration and an unbalanced response.
Shear walls are effective structural elements used mainly in multi-story buildings to provide resistance against lateral loadings such as earthquake and wind loadings. There are several types and shapes of shear walls depending mainly on geometry and height of the building. Both type and shape of the shear wall affect the efficiency of resisting lateral loadings. In this study, fifty six building models have been analyzed using the finite element method by using the SAP2000 V14 computer program. Each model have ten stories, subjected to earthquake loadings, with various numbers of bays, and with three types of shear walls, namely: side shear walls, middle shear core, and double shear cores, provided that each type of the shear walls (or cores) has the same material volume. The analysis outputs have been investigated to select the appropriate type and location of the shear walls (or cores) for the multi-story buildings subjected to earthquake loadings. Specified conclusions have been presented to obtain the optimum behavior for the multi-story buildings under the effects of earthquake loadings.