×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerDesired mechanical properties like microstructure, micro hardness and wear resistance are the key parameters for which low carbon steel (AISI 1006) are widely selected. Surface heat treatment applied to improve these properties; traditionally surface heat treatments like induction hardening, in recent time’s laser surface hardening. In this work, thermochemical treatment (liquid nitriding) by using mixture from 61% NaCN, 15% K2CO3 and 24% KCL and followed by Nd:YAG laser surface treatment was done . The laser parameter were energy (0.89, 2, 4 and 9) J, spot diameter (0.790 ,0.33, 0.283 and 0.224) mm, pulses duration (1, 2.33, 4.47 and 9.87) ms with fix wavelength 1604nm. Laser surface treatment cycle was melting the layer surface, holding and rapid cooling in air medium. Optical microscopy (OM) and scanning electron microscope (SEM) has been used to study the microstructures and cross-sectional of molted and heat affected zones respectively. The wear test was done to measure the wear rate by using pin -on-disk principles were satisfied. The result shown that increasing in laser energy effects to increase in the area of melted and heat affected zones of nitriding steel. Also increasing in laser energy led to increase micro hardness about 61%, while wear rate decrease about 40 % and increased depth of molted zone.
This paper presents a comparison of using different techniques for stir spot welding of Aluminum 2024-T3, which are refill friction stir spot welding (RFSSW), edited (RFSSW-pin) and conventional friction stir spot welding (FSSW), depending on the obtained tensile shear strength property. Specimens were prepared from AA2024-T3 sheet for chemical analysis and mechanical tests. Workpieces were stir spot welded utilizing the above mentioned techniques at four rotational speeds (2000, 2500, 3000 and 4000 rpm) using tool pin diameters (5 and 7 mm) for conducting the tensile shear tests. The microhardness along the cross section of the welded specimens was conducted at the best conditions as well as the microstructure examination. The comparison results revealed that at the rotational speeds (2000 and 4000 rpm) in both cases of tool pin (5 and 7 mm), the ultimate tensile shear force was slightly higher than that for other speeds. However, the ultimate tensile shear force was found higher at 3000 rpm speed with a tool pin 7 mm. The microhardness results manifested a W-shape at the best conditions. Finally, the microstructure examination depicted the morphology of the main zones of the weld joint.
In this study the friction stir lap welding was carried out by a new technique (diffusion bonding phenomenon) between (AA1100 and low carbon steel C10 sheets of 3mm and 1mm thickness respectively. These alloys have difference ranges in melting temperature and other physical properties. Different parameters were used: tool rotation speeds (630, 1250) rpm, travel speeds (80, 32) mm/min. and pin length (2.8,3) mm using cylindrical threaded pin. Many tests and inspections were performed such as tensile shear test and X-Ray diffraction tests. Microhardness and microstructure observations were conducted by using optical and SEM. The above tests were used to evaluate the weld quality and joint efficiency under different welding parameters. Best result for FSLW by diffusion phenomenon appear in (low carbon steelC10 / AA1100-H112) joint at 1250rpm in 32 mm/min. with 2.8mm pin length and the maximum tensile shear strength was (3.9)KN.It was found that the highest micro hardness was (138HV) at the interface between the low carbon steel and AA1100.
Friction stir spot welding (FSSW) is a modern solid-state joining process able to weld similar and dissimilar overlap joints in different classes of materials and is widely being considered for automotive industry. In this work, the mechanical behavior ) i.e. tensile shear tests, Microhardness(, and microstructure of friction stir spot welded joints were studied for AA6061-T6 aluminum alloy sheets with thickness of 1.6 mm. Series of FSSW experiments were conducted using vertical CNC milling machine type "C-tek". FSSW is carried out at different pin profiles (cylindrical, taper, and triangular) and tool rotational typically speeds, i.e. 800, 1000, 1200 and 1400 rpm. Based on the welding experiments conducted in this study, the results show that sheets welded by triangular pin tool have highest tensile shear load, of 3.2 kN, followed by welds with cylindrical pin, while welds made using taper pin has the tensile shear load 2.1 kN at optimum speed of 1200 rpm. Also the pin shape and rotational speed had an obvious effect on microstructural parameters i.e. hook height and bond width.