×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerIn this work , experimental investigation has been done for free-convection heat transfer from rectangular fins array on a heated horizontal base plate to surrounding air in the steady-state flow condition with rectangular notch portion effects. Five cases of fins arrays have been employed . One case without notch and other cases with rectangular notches for different percentages of aspect ratio area removal from fin . The horizontal base plate has been heated with various electrical supplied power values. Different number of fins and spacing have been used . The effect of notches from fins on average convection heat transfer coefficient and average Nusselt number at constant aspect ratio of fin height to fin length and varying heat inputs to the heating element have been discussed . The experimental results show that the performance of notched fins array in term of average convection heat transfer coefficient is 28% to 45% higher than unnotched fins array. The present experimental results have been compared with previously works . The results show a good a greement.
Numerical and experimental investigation on the turbulent enhancement convective heat transfer inside slot and plain dimples tubes with internal twisted tape were performed in this study. An experimental rig was constructed and instrumented to evaluate the heat transfer enhancement and pressure drop at this surface. Air was used as working fluid, and steam was used as a heating source where constant wall temperature condition of (135C?) was achieved. Heat transfer and pressure drop data were obtained from four configuration tube. The test facility was capable for providing turbulent flow with Reynolds number varied from 4000 to 15000. Thermal and hydrodynamic flow pattern was numerically studied using commercial code FLUENT15. The average heat transfer of the experimental results was in good agreement with the numerical ones. The result depict that the slot dimple tube with twist tape and plain tube with twist tape give high enhancement in heat transfer relative to plain tube due to increase in area of heat transfer. The average enhancement ratio for slot dimple tube with (TR =4 and 8) are (1.204 and 1.202) respectively .This indicates that 15.5-20.4% of heat transfer area can be saved at the same pumping power for present cases configuration compared with the plain tube heat exchanger.
Computational and experimental investigation of fluidic thrust vectoring using counter-flow method had been carried out in the present work. The experimental investigation involved the design and construction of a test rig for a circular duct to examine the effect of various geometric variables on the thrust vectoring angle. The experimental tests covered Coanda surface radius R/d = (0.58823, 1.17647, 1.75471), secondary gap height h/d = (0.02941, 0.05882), over a secondary mass flow ratio range (0 ?
In the present work, the agricultural wastes which are wheat bran and raw okra waste used as adsorbent material for adsorption of cadmium and copper ions from wastewater .The effect of adsorption variable which include initial pH of solution , agitation speed, agitation time, initial concentration of cadmium and copper ions, and amount of adsorbent material were investigated in a batch process in order to obtain the maximum ions removal from wastewater .The results obtained from experimental investigation show that the percentage removal of metal ions increases with increasing pH and agitation speed until a maximize value after that it decreased with increasing pH and agitation speed. Also increases with increasing amount of adsorbent material and agitation time until a maximize value then reach a constant value approximately , and decreasing with increasing metal ions concentration .The maximum removal percent of cadmium and copper ions were 85.8% and 52.7 % respectively which obtained at pH equal 5.0, agitation speed 150 revolution per minute, agitation time 105 minute , metal ion concentration 40mg /L ,and adsorbent amount 1.5gm when using wheat bran as adsorbent material ,while obtained the maximum removal percent of cadmium and copper ions were 81.7% and 47.8 % which obtained at pH equal 6.0, and pH equal 5.0 respectively , agitation speed 150 revolution per minute, agitation time 90 minute ,metal ion concentration 40 mg /L ,and adsorbent amount 1.5gm when using okra waste as adsorbent material. From above result the wheat bran and okra waste was a best adsorbent material for removal cadmium and copper ions from wastewater but wheat bran slightly more effective than okra waste._x000D_
Natural convection air heat transfer and fluid movement currents around a hot circular cylinder inside an inclined triangular enclosure has been analyzed experimentally. Three different sizes of an enclosure with a long side of 20, 25, and 30 cm, the thickness of 1 mm, and depth of 50 cm were used in the present work to give three radius ratios. The effect of Rayleigh number, radius ratio, the rotation angle of triangle enclosure, and the inclination angle of the apparatus with horizontal axis ? on the heat transfer process was investigated. The ranges of these parameters were: Rayleigh number from 5×106 to 2.5×108, radius ratio (0.345, 0.455, and 0.618), rotation angle (0o, 45o, and 90o), and inclination angle (0o, 45o and 90o). The results show that the heat transfer rates increase with increase in Rayleigh number and as the rotation angle of enclosure is changed from 0o to 90o. Moreover, the heat transfer rate increases linearly with Rayleigh number at higher radius at rotation angle 0o, 90o only. While, it increases slightly with Rayleigh number at rotation angle 45o. Additionally, the higher heat transfer rates occur at vertical position of enclosure inclination angle 90o and rotation angle 0o (the base of triangle at the bottom) and it decreases as inclination angle deviates from 90o to 0o. This behavior is reverse completely at higher radius ratio 0.618. Empirical correlations for the average Nusselt number has been found to depend on Rayleigh number., radius ratio, rotation angle and inclination angle.
Computational and experimental investigations of thrust vectoring using co flow method had been carried in the present work. The experimental investigation included design and construction of rig with rectangular duct with aspect ratio (4.4) in order to investigate the effect of various geometric variables on thrust vectoring angle. Set of experiments tests carried out over the mass flow ratio ( ) range 0 ? ? 0.23, gap height h/H= (0.0294, 0.0588, 0.088 and 0.1176) and coanda surface diameter ?/H= (1.176, 2.353 and 3.529). _x000D_ Load measurements were obtained using four load cells. The computational investigation involved a 3D numerical solution by FLUENT 6.3.26 Software for some of experimental cases. The results show that the increase in secondary jet blowing rate lead to increase the jet vectoring angle, there are three zone can be observed, dead zone appears at low mass flow ratios, then followed by control region in which continuous thrust vector control can be achieved followed by a saturation region. The coanda surface diameter determines the length of the dead zone, which a small coanda surface used for coanda effect resulted in a prolonged dead zone range and the secondary gap height to the primary gap height had inverse relation with jet vectoring angle. The investigation shows that both the experimental and computational results obtained follow a similar trend line.
The investigation of the existence of a tempera-ture change with pressure inside the pneumatic cylinder chambers during the charging and dis-charging strokes in the pneumatic cylinder is ex-perimentally demonstrated. Three different varia-bles (pressure, piston displacement and tempera-ture) were measured in this work while operating with a servo pneumatic system and a discussion of the relationship between these variables was pre-sented. The cylinder used has a piston diameter of (0.05m), piston rod diameter (0.02m) and a stroke length of (0.2m). The results show a temperature rise of 23 K above atmospheric temperature at chamber (1) while air compressing and a tempera-ture drop of 17 K below atmospheric temperature at chamber (2) while air expansion and measures other temperature changes also.
Experiments were conducted to study the effect of quenching medium carbon steel in water-based MWCNTs nanofluids at 0.05 % wt. concentration quenchant, a large cylindrical sample with 46 mm diameter and 40 mm length made from medium carbon steel used with three K-type thermocouples with a diameter of 1.5 mm inserted in three locations for sample (center of the sample, mid-point between center and surface and 1 mm from the surface). A time-temperature reading data system was used to read temperature history during cooling stage.The same experiments were simulated using ANSYS Workbench with Thermal Transient Version 19, the cooling curves at three locations for the cylindrical steel sample calculated during quenching in MWCNTs nanofluids. Quench factor analysis was used to predict the hardness results from the calculated and measured cooling curves, and these results compared with the hardness test results conducted in the significant sample from the center to the surface. The results show excellent compatibility when compared between the hardness results from cooling curves, and it also shows a good agreement with the results of the hardness test, especially at the sample surface.
A theoretical and experimental investigation pertaining to the buckling behavior of slender fiber reinforced polymer columns subjected to axial loading under varying temperatures (from room temperature to 50?). Two groups of composite materials were used for manufacturing of test specimens, the first consist of perlon fiber as a reinforcement and acrylic resin as a bonding matrix, while the second consists of a combination of perlon and carbon fibers as reinforcement. The composite specimens were fabricated by vacuum molding technique and cut according to ASTM D-638 for conducting tensile test. The data from tensile test were used to calculate the effective slenderness ratio and defining the column as Euler buckling column. An experimental rig was designed, manufactured and calibrated to study the effect of thermal and buckling load subjected to columns.Numerical analyses pertaining the buckling behavior for both groups were conducted. The results show that the temperature has a considerable effect on properties of fiberreinforced polymer composites where the value ofcritical load and Young's Modules decrease withthe increase of temperature for both groups.Perlon & Carbon reinforcement composites gavebest mechanical properties, which make them thebest candidate to improve the buckling resistancecharacteristics of composite materials.
Forced vibration has been experimentally investigated on a model consists of circular pipe with1.6m length. The pipe built in tank (1.2m length, 0.6m height and 0.6m width) horizontally at 0.4m height with two different diameters d=15mm and d=35mm. The pipe conveying laminar flow in the fully developed region, of Reynolds number equals 2000. The experimental results of span pipe conveying water at five stations of forced excitation vibration were studied. The harmonic forced vibration with two different excitation frequencies (10 Hz and 15 Hz) are imposed at all of the five locations. The distance between two stations is (0.2m). Two conditions of pipe environment have been applied, the first in air and the other was immersed in water. It is concluded that the effect of flow induced vibration due to the pipe conveying fluid increases the maximum deflection when the fluid speed increases. The water surrounds the pipes reduce the effect of excitation vibration about (33 – 46%). The effect difference between the excitation frequencies was about (4 – 7%).
An experimental investigation has been performed to study the effect of combined artificially roughened (ribs) with and without single Large Eddy Break-Up Devices, on flow and heat transfer characteristic of fully developed turbulent flow in rectangular duct. The aspect ratio of rectangular duct is 10, hydraulic diameter 72.72 mm, relative roughness pitch (P/e) 10 and relative roughness height (e/Dh) 0.05. The rib was in the form of circular shape with diameter of (4mm) which was mounted on heated wall of duct at spanwise direction. The experiments have been conducted by varying airflow rate in terms of Reynolds number ranging from 3.2x104 to 6.2x104 and constant heat flux of 600W/m2. The heat transfer and friction factor of the flow for rib and combined method were compared with those of a smooth duct under similar experimental conditions. It has been found that the combined method (rib with single Large Eddy Break-Up Devices) has significant effect on the friction factor and heat transfer with decreasing in friction factor with percent(1.2) and increasing Nusselt number with (4.1). Correlations for Nusselt number and friction factor in terms of (Reynolds number and Large Eddy Break-Up Devices) parameters are found which reasonably correlate the experimental data.
The composite opened web steel joist supported floor systems have been common for many years. It is economic and has light weight and can embed the electrical conduit, ductwork and piping, eliminating the need for these to pass under the member, consequently eliminate the height between floors. In order to study the joist strength capacity under the various conditions, it had been fabricated seven joists composed of the steel and concrete slab connected to the top chord by shear connectors (headed studs). These joist have 2820 mm length c/c of the supports and 235 mm overall depth. In the present study, six variable parameters are adopted (Studs distribution, Degree of shear connection, Degree of the web inclination, Shape of the web, Density of concrete for slab and length of the shear connector). The test results exhibited that minimum strength capacity was 160kN for light weight joist and maximum capacity was 225kN for joist of long shear connectors at failure. The results were compared by ultimate flexural model by Azmi.
The partial shading conditions have a significant effect on the performance of Photovoltaic system and the ability of delivering energy. In this study, the impact of different partial shading on the mono crystalline (88W) PV module performance was investigated in this study. Horizontal string, vertical string, and single cell shading at different percentage of shading area have been studied. It is found that the horizontal string shading is more severe on the efficiency of the PV panel. In contrast, the efficiency of PV panel with cellular and vertical cell shading was less during the tests. The experimental results showed that the power losses were 99.8%, 66% and 56.8 % for horizontal, cellular and vertical shading respectively via applied non transparent material as shading element by 100% of shading area at 500 W/m2. Moreover, transparent material used to shade whole module horizontally, different shading area and different radiation level applied to find electrical characteristics of the module under these conditions. The results show that at 800W/m2 of irradiation levels and no shading condition the power was 68.6W, by increase shading area by 20% in each step, the power reducing by 44.94, 47.58, 49.42, 50.57 and 52.4% in compared with their initial value at no shading condition.
Recently, major part of convection heat transfer researches focus on increasing fins efficiency by increasing thermal performance for the same fin volume. Metal foam is a promising way to achieve this aim. Performance analysis has been carried out to investigate the heat transfer characteristics of copper fin foam samples. The samples have been compared with the solid metal fin heat transfer. A forced convection heat transfer had been applied to a four specimens. An electrical heater heats up the fins, which are subjected to a stream of the ambient air driven by a blower fan as heat dissipated. The heat flux had been fixed along the tests with three different air velocity used; the forced heat convection had been simulated. The pores density of copper fin foam is varied in the range of 10, 20 & 40 pores per inches (PPI). Thermal performance of copper fin foam has been evaluated in terms of average Nusselt number and thermal resistance of heat sinks. The increasing in the heat transfer rate and average Nusselt number when used metal foam has been found in the range of 36-133 % compare to solid copper. Furthermore, it has been proven that this increment reaches the maximum value for a given PPI even when raise the air velocity.
The consequence of mixing pure ethanol with gasoline on the pollution and performance of SI engine are investigated experimentally in the existent study. The SI engine that employed in the experiment is a single cylinder four stroke. Analysis is carried out for engine operation parameter, CO2, CO and unburned HC productions. The measurements are recorded for several engine speeds from 1500 – 3000 rpm with load and ethanol addition of (0E, 10E, 20E, 30E, 40E, 50E,). The results displayed increasing in brake power, and brake thermal efficiency while the brake specific fuel consumption decreases when the ethanol- gasoline blends fuel increases. Also it was found that CO, HC, and CO2 concentrations decrease when the ethanol- gasoline increases. The best results obtained in the study is for the blend of E-50.
Fused deposition modeling (FDM) is a commonly used 3D printing technique that involves heating, extruding, and depositing thermoplastic polymer filaments. The quality of FDM components is greatly influenced by the chosen processing settings. In this study, the Taguchi technique and artificial neural network were employed to predict the ultimate tensile strength of FDM components and establish a mathematical model. The mechanical properties of ABS were analyzed by varying parameters such as layer thickness, printing speed, direction angle, number of parameters, and nozzle temperature at five different levels. FDM 3D printers were used to fabricate samples for testing, following the ASTM-D638 standards, using the Taguchi orthogonal array experimental design method to set the process parameters. The results indicated that the printing process factors had a significant impact on tensile strength, with test values ranging from 31 to 38 MPa. The neural network achieved a maximum error of 5.518% when predicting tensile strength values, while the analytical model exhibited an error of 19.376%.