×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerPlatinum, copper, and nickel were founded the best metals used in resistance temperature detectors RTDs. They commonly used in laboratory and industrial applications because they provide accurate and reliable measurements in a wide temperature range from (- 200 to 850 °C). They have high conductivity, sensitivity, and hardness to resist strain shock, pressure, and vibration. The accuracy level of them depends on reliability, stability, repeatability, linearity, and response to time. This study aims to determine and compare the accuracy of these three metals in regarding to their features which include stability, repeatability, and response time. The study has gathered and analyzed the data of these suitable and precise metals and compared with each other. The results showed that platinum is widely needed for RTDs due to its precision, stability, higher accuracy, and linearity output, while copper and nickel are not stable or repeatable as platinum. It was indicated that temperature coefficient of resistance TCR for nickel is bigger and for copper is medium, but for platinum is lower.
The experimental analysis is conducted under the Iraqi climate conditions to investigate the performance enhancement of a solar updraft tower system (SUTS) using the porous copper foam as an absorber plate and conventional absorber plate with absorber inclination angle of 18°. In the present work, a semicircular collector is divided into two identical quarter thermal collectors to become two identical SUTS. One of the quarter circular thermal collectors contains on the metal foam as an absorber plate, while the other quarter collector on the conventional flat copper absorber plate. In this study the air inlet height is changed of (3, 5, and 8) cm. The experimental tests carried out in Baghdad city (latitude 33.3° N). Results showed that the air inlet height variation caused to enhance the solar updraft tower performance. The highest values was recorded when the air inlet height is 3 cm using porous absorber compared to flat absorber plate. Copper material foam as an endothermic surface causes a marked decrease in average surface temperature of the plate. The maximum hourly thermal efficiency of solar collector was increased to about 41.6 % and the maximum enhancement of the power output to about 45.2 % compared with flat absorber plate.
The electrodes material plays an important role in the amount of electricity produced in microbial fuel cells (MFCs). Metal electrodes used in MFCs are subject to biological and concentration cell corrosion which leads to a decrease in the cell efficiency. In the present work, the corrosion behavior of three selected electrode materials, namely, stainless steel, copper, and zinc under different operating conditions was investigated and discussed. In anode chamber, the microorganism (MO) used was Saccharomyces cerevisiae (yeast) with sodium acetate as a substrate forming the microbial corrosive solution. In the cathode chamber, the corrosive solution is aerated water. The effects of different operating parameters on the corrosion rate (CR) of these electrodes were studied such as: microorganism concentration, aeration of cathode chamber, and flow velocity in cathode chamber. The potential of the each electrode was measured to understand the corrosion behavior of electrodes and the produced current was also investigated. It was found that the corrosion rate of the electrodes in both anode and cathode chambers increases with increasing MO concentration in anode chamber and with increasing agitation speed in cathode chamber. The bio-corrosion is an important part of the corrosion occurring in microorganism chamber. The stainless steel exhibited the lowest corrosion rate for the whole investigated range of operating parameters followed by copper. The zinc electrode was found to be poor as an electrode in MFC as its corrosion rate was very high in all conditions investigated. In addition, this study showed that the air pumping in water chamber causes an appreciable increase in the corrosion rate in both chambers and an increase in the produced current.
The presence of heavy metal pollutants in refinery effluent significantly impacts the corrosion rate of carbon steel. The focus of this research is to analyze the impact of various inorganic pollutants, including copper, vanadium, nickel, and chromium ions, on the corrosion of carbon steel across different solutions. After conducting a thorough examination of various operating conditions, including pollutant concentration (ranging from 300-3000 ppm), temperature (30-60? C), and flow velocity (0-800 rpm). Our research shows that copper ions have the highest corrosion rate, with vanadium ions being a close second. Conversely, nickel and chromium had the most negligible impact on corrosion rate and, in some instances, even exhibited corrosion inhibition effects. It was also observed that an increase in flow velocity and temperature significantly amplified the corrosion rate of the metal ions investigated.
An experimental and theoretical study of free convection heat transfer for a cylinder placed in an iron test section of dimensions (0.2x0.2x0.2 m3), the test section filled with saturated porous material glass balls (5 mm), and the air is the working fluid with Raleigh number (7692.6 ? Ra ? 17654). The circular cylinder heater (D = 0.015 m, L = 0.2 m) is heated electrically, made of Copper and located in different positions (in X & Y direction). The theoretical part includes solving the free convection heat transfer using the ANSYS program (fluent). The experimental and theoretical results showed that the surface temperature values around the cylinder perimeter when changing its position within the test section are changing as moving up and down where the effect of buoyancy force appears. The maximum difference between the upper and lower position at the experimental result is 7.22%, and the average Nusselt number increases with Raleigh number and heat flux. Also, the experimental results showed that the use of porous material significantly improves the heat transfer by 48.6%. The maximum percentage change between the experimental and theoretical results is 5.46%. Moreover, experimental correlations were achieved, and a comparison was performed between the present results with the previous studies and it gives a good agreement.