×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerMagnesium oxide nanoparticles were deposited by laser pyrolysis process. Three types of lasers were employed CW CO2, Q-switched Nd-YAG (short pulses) and long pulses Nd-YAG lasers. The size and density of nanoparticles vary with laser energy, power, pulse duration and the scanning speed of the laser. In this method, MgO nanoparticles were deposited by a laser beam on a quartz substrate from aqueous solution of magnesium nitrate. AFM images reveal formation of small nanoparticle size of 24.5 nm with surface roughness 6.97nm by Q-switched Nd-YAG laser (10 ns) when the energy was 1J. While for CO2 laser, the smallest size was 18.8 nm at 0.4mm/s scanning speed with surface roughness 5.21nm at the same scanning speed. Moreover, long Nd-YAG pulses laser produces relatively larger average size of 37.5nm at 0.8ms pulse duration. The absorption spectra from UV-Visible spectroscopy were also conducted. The best absorption intensity was obtained at a wavelength ranging between 420-430 nm for both lasers. Finally, Thermal analysis using COMSOL Multiphysics software for the deposition process reveals that maximum temperature about 440Kfor Q-Switched Nd-YAG laser at 1J laser energy. While for RF CO2 laser, the maximum temperature obtained at 0.4mm/s scanning speed is 850K.This work provides a good knowledge for the deposition of nanoparticles using laser beams.
The emission sources have great effects on our environment. Further using of fossil fuels because of our needs for heating purposes and developments leads to raising the emission concentration in the air which caused to health risks to human society and its environment. This paper deals with using a different percentage of Iraqi liquefied petroleum gas from 10% to 25% with different percentage of Iraqi Gas-oil fuel from 90% to 75%, keeping the thermal load constant in order to indicate the possibility of reducing the pollutant emissions . A dual fuel burner and equivalence ratio range from 0.8 to 1.4 is used to study the emission concentrations based on these equivalence ratio. For further reducing in emission and heat recovery from the exhaust gases the cooling effect also investigated for water mass flow-rate from 12 kg/s to 48 kg/s roughly. The results showed that for further increasing equivalence ratio the UHC, CO, and Soot increased by about 3% and NOx, and CO2 decreased by 2.5% and this due to decreasing the oxygen ratio in the mixture and incomplete combustion occurred. Also for increasing percentage participating of LPG fuel as a secondary fuel, UHC, CO, and Soot decreased by 8%and NOx and CO2 increased slightly. With heat recovery process the concentration of UHC, CO, and Soot increased slightly while NOx, CO2 decreased by 1.5% because of decreasing of combustion chamber temperature.
The consequence of mixing pure ethanol with gasoline on the pollution and performance of SI engine are investigated experimentally in the existent study. The SI engine that employed in the experiment is a single cylinder four stroke. Analysis is carried out for engine operation parameter, CO2, CO and unburned HC productions. The measurements are recorded for several engine speeds from 1500 – 3000 rpm with load and ethanol addition of (0E, 10E, 20E, 30E, 40E, 50E,). The results displayed increasing in brake power, and brake thermal efficiency while the brake specific fuel consumption decreases when the ethanol- gasoline blends fuel increases. Also it was found that CO, HC, and CO2 concentrations decrease when the ethanol- gasoline increases. The best results obtained in the study is for the blend of E-50.
Laser annealing represents a powerful method for tailoring the properties of silver nanofilms on quartz substrates, offering advantages in terms of precision, scalability, and functionalization. Continued research efforts are expected to deepen our understanding and broaden the applications of this promising technology in diverse fields. In this work, laser annealing of silver nanofilms deposited on quartz substrates was performed and investigated. RF CO2 laser of variable power in the range 1–20 W with beam quality of 1.1 was used to anneal silver nanofilms. AFM analysis emphasized that nanocrystal sizes of 60 nm were obtained for silver nanofilms. Furthermore, the optimum absorbance peak occurred at about 449 nm for smaller film thickness. Thermal simulation and analysis of the annealing process were also conducted using COMSOL Multiphysics software. It was observed that optimal temperature of 729 K was achieved when 10 W laser power and 2 mm/s scanning speed were used to anneal 20 nm silver film thickness. Design of expert analysis was also used to better understand the laser annealing process of silver nanofilms since convolution of several process parameters affect the process output.
Photonic crystal fibers (PCFs) are generally divided into two categories: solid-core photonic crystal fibers and hollow-core photonic crystal fibers. In this paper, a long-period fiber Bragg grating (LPFBG) was experimentally fabricated in a hollow-core photonic crystal fiber (HC-PCF) using a CO₂ laser and based on the point-by-point technique. Proper LPFBGs were inscribed using laser powers of 0.9 W and 1.4 W, with grating parameters (grating period, length of each pitch, and depth of each pitch) equal to (136 µm, 48.042 µm, 16 µm) and (142 µm, 74.027 µm, 22.09 µm), respectively, for two samples. The Bragg wavelengths and full-width at half-maximum (FWHM) were (1529.274 nm, 1.34 nm) and (1529.629 nm, 5.11 nm), respectively, for the two samples fabricated using CO₂ laser powers of 0.9 W and 1.4 W. From these results, it was recognized that the optimal LPFBG-HC-PCF was the one fabricated using 0.9 W laser power. The unique structure of hollow-core photonic crystal fibers, which enables light propagation within the air core and provides a large internal surface area, has attracted significant research interest for various sensing و communication applications, Environmental and Biological Monitoring, and medical applications.
A rapidly expanding global population has heightened the need for engineering technologies aimed to enhancing the mechanical properties of weak soil, raising concerns about the sustainability of engineering practices that depend on energy-intensive materials and methods from earlier times. Traditional ground improvement techniques like compaction, preloading, vibration, and chemical grouting are typically costly and frequently have very high energy and CO2 footprints. Soil stabilization employing bio-enzymes has been viewed as a resilient and ecologically beneficial method for modifying the soil characteristics. Calcite-induced precipitation methods have recently become potential techniques in geotechnical engineering for improving the shear strength of soils. One of the most promising methods among them is enzyme-induced calcite precipitation (EICP). Enzyme induced calcite precipitation (EICP) is a bio-inspired technique based on the precipitation of calcium carbonate for enhancing the geo-mechanical properties of soils. In this technique, calcium carbonate acts as a cementitious agent that binds the soil particles together at the points of contact hence, increasing the strength and stiffness of treated soils, while relatively reducing the soil permeability and porosity. The achieved enhancements make EICP useful for applications such as ground improvement, construction materials, and erosion control over traditional binders. It is an environmental friendly technique that has generated great interest to geotechnical engineers. EICP particularly, has proven to be more effective since its application to all soils coarse and fine which have small pore size. This review thoroughly assesses the use of the EICP approach as a soil stabilization strategy conducted by various researchers. This review article studies urease and its implication on the characteristics of treated soil such as shear strength, permeability and micro-structural changes.
This paper provides a comprehensive overview of microfluidic device (MFD) manufacturing processes. The review starts with an introduction elucidating the significance and advantages of MFDs. Subsequently, a brief description of the materials employed in MFD fabrication is presented. The manufacturing process used to create MFDs is then thoroughly examined, with a focus on the application of laser technology.