×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerMoisture-induced damage in asphalt pavements, is defined by adhesive failure at the binder-aggregate interface and decreased mechanical integrity, severely reduce pavement durability. The research examines the mechanical properties and moisture sensitivity of hot mix asphalt (HMA) enhanced with styrene-butadiene-styrene (SBS) polymer and including reclaimed asphalt pavement (RAP). Laboratory assessments, including indirect tensile strength (ITS) and tensile strength ratio (TSR) tests, were performed on conventional HMA, SBS-modified HMA (4% SBS), and SBS-modified HMA contained 20% RAP. The results indicated that SBS modification significantly improved mechanical and moisture resistance properties, where unconditioned ITS specimens increased by 37.1% and TSR value enhanced by 13.5%. The incorporation of RAP decreased ITS value by about 21 % relative to pure SBS-modified HMA; nevertheless, the SBS+RAP combination still show higher ITS and TSR values than conventional HMA.
Hot mix asphalt embedded on "Reclaimed asphalt pavement"(RAP) has the advantages of high technology. Moisture damage is a concern in these mixtures at all service temperatures. Therefore, the performance of this mixture against moisture at all service temperatures was considered a target of this research study. In this way, the effects of humidity on the performance of varieties were investigated using experimental methods including tensile strength ratio (TSR). In the framework of this study, Four different ratios of RAP for each of the surface and bonding layers (10%, 15%, 20%, 25%) and (30,40,50,60)% were added to the hot asphalt mix (HMA) for the two layers respectively to study and find the content Optimal RAP for both layers RAP through Marshall stability and hygroscopic resistance of asphalt mixtures through moisture damage is examined. The ratio (TSR) of the mixtures containing the optimal RAP content is compared with the asphalt mixture without RAP for three fillers and for both layers. The results showed a slight decrease in the tensile strength of the (HMA) that does not contain RAP compared to the asphalt control mixtures containing the reclaimed pavement, where it was found that the percentages were slightly higher and still higher than 80%. The results indicate that in general, Although there are old materials in the hot asphalt mix (HMA) produced from RAP, which include aggregates and bitumen binder surrounding the aggregate particles, the performance of these mixtures and integrations against moisture damage. Because it contains this, it can have results with “hot asphalt mixtures” containing RAP for areas with damage without worry in addition to good natural curbs.
Moisture damage in terms of stripping; and aging surface in terms of raveling and abrasion are among the primary distresses that lead to the deterioration of asphalt pavement, diminishing the overall quality and functionality of road surfaces. This study investigates the impact of using low-cost and locally available waste aluminum scrape powder (WASP) with a particle size ranging from sieves No.8 to No.200. WASP exhibits a high bulk specific gravity and melting point temperature on HMA mixtures, which could also potentially enhance the density and stiffness of modified mixtures. Five quantities of additives 0.5, 1.0, 1.5, 2.0, and 2.5% have been used to enhance the mechanical-durability features. The aggregate sources of AlDoz and AlNibaa'e were chosen, and different mixtures were produced utilizing Marshall and Roller compaction methods. The study's findings indicated that WASP enhanced mechanical-durability characteristics and reduced the asphalt mixture's sensitivity to abrasion, moisture damage, and aging. The optimal amount of WASP was determined to be 1.5%. In addition, based on the influence of the aggregate source and compaction technique, it is visible that the AlNibaa'e source and roller compaction mode provide superior outcomes compared to the AlDoz aggregate source and the Marshall method.
Open-graded-fraction-course (OGFC), is a hot asphalt mixture usually utilized as a private purpose wearing course, because of open graded asphalt mixture and aggregates skeleton (stone-on-stone) contact, it contain a relatively high air voids’ percentage, after compaction which are permeable to water. In this research one type of gradation was used (12.5 mm) NMAS, to preparing the OGFC asphalt mixtures, penetration grade 40/50, crushed aggregate, asphalt content prepared with 4 % and up to 6 % by weight of mixture with 0.5 % increments. Optimum asphalt content (OAC) was selected based on these criteria, air voids content, asphalt draindown, permeability, and abrasion resistance (aged and un-aged) condition. The mix performance had been investigated by indirect tensile strength and moisture susceptibility (sensitivity) measured according to the (AASHTO T283-14). Results illustrate that the increasing of asphalt binder content leads to a decrease of the air voids content, abrasion loss and permeability values, while draindown increase, conversely, the indirect tensile strength (ITS) had been significantly increased for both conditions and this is a gaod suggestion to resistance alongside moisture susceptibility. It can be decided that the increasing of asphalt binder percent in OGFC asphalt mixture, leads to an increase in the thickness of binder coating around the aggregates. On the other hand, the influence of modifier that prepared with 4% styrene-butadiene-styrene (SBS) on OGFC asphalt mixture tends to improve the mix properties and exhibit higher (TSR) as compared with original asphalt by (31, 27.7 and 24.4) % at asphalt percent (4.8, 5.3 and 5.8) %, respectively. The SBS improved the adhesion between aggregate and asphalt which leads to reduce stripping of HMA, horizontal deformation, and increased the tensile stiffness modulus value.