×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerThis study investigated numerically and experimentally fluid flow and heat transfer in the desktop PC. Three patterns of the positions of air inlet and outlet were tested to find the best one for cooling. The computer components in the present study are CPU, finned heat sink, power supply, motherboard, CD, HDD and fans. Three components which were generate heat are CPU, motherboard and power supply and there were two openings for air inlet and two for air outlet. The air inlet velocities were 1.2, 1.8, 2.4 m/s with constant CPU fan velocity. The studied parameters were the changed of inlet air velocity, powers of CPU, motherboard and PSU and the positions of inlet air. The numerical results obtained are found in a good agreement with the experimental results. The experimental results show that the maximum temperature was 81 at 16.5 W and 1.2 m/s. Numerical results showed that the CPU temperature reaches 89.6 at 18.5 W and 1.2 m/s. From the results, it was found that; the temperatures of the main components (PSU and motherboard) affected little by CPU power and vice versa, the finned heat sink has higher cooling efficiency and the pattern 1 was the best pattern for CPU cooling.
The efficiency of the solar PV panel decreases significantly as the PV panel’s operating temperature increases. There are many cooling techniques might be suitably deal with this problem to enhance the solar panel efficiency. The presented cooling technique used for solving the PV panel’s temperature elevation is an active close loop cooling system, accomplished using two water glazing chambers made from acrylic glass placed at the PV panel surfaces (rear and front). These champers are utilized for cooling down the PV cell’s temperature, as well as filtering the useful sunlight spectrum. The results show that the PV cell’s temperature reduction by 50.06% with using the cooling system, this leads to an average increase in the maximum output power and consequently electrical efficiency of the PV panel by about 12.69% and 14.2%, respectively.
Cooling greenhouses is essential to provide a suitable environment for plant growth in arid regions. However, using conventional cooling methods are facing many challenges. Filtering out near infra-red radiation (NIR) at the greenhouse cover can significantly reduce the heating load and can solve the overheating problem of the greenhouse air temperature. Four cases of shadings were examined for their ability to improve the indoor condition of a greenhouse cooled by indirect direct evaporative cooler: (shade 1) a single layer of polyethylene film, (shade 2) a double layer of polyethylene film, (shade 3) a double layer of polyethylene film with a green mesh layer (shade 4) a double layer of polyethylene film with a Utrecht Corrugated Cardboard with 3cm holes distributed for incident sun light. An experimental study is conducted to determine the performance parameters of indirect direct evaporative cooling of greenhouse in Baghdad (33.3 oN, 44.4oE) for the four types of shadings. It was found that the percentage reduction in light intensities for shade 1, shade 2 and shade 3 are 15%, 25% and 40% respectively. It percentage reduction solar intensity due to shades is increases at the beginning and ending of sunny period, while it was minimum at noon. The percentage reduction in temperature due to indirect direct evaporative cooling for the shade1, shade 2 and shade 3 and shade 4 are 32.4, 36.3, 42.4, and 47 respectively. The percentage increasing in relative humidity due to indirect direct evaporative cooling for the shade1, shade 2 and shade 3 and shade 4 are 562.5, 729, 871, and 788 respectively. The percentage increasing in temperature due heating load of greenhouse for the shade1, shade 2 and shade 3 and shade 4 are 41.4, 33.2, 20.5, and 11 respectively. The percentage decrease in relative humidity due heating load of greenhouse for the shade1, shade 2 and shade 3 and shade 4 are 43.4, 31, 11.8, and 7 respectively.
The control of quenching process has been investigated in this study by developing a quench system design to simulate the quenching process and measure the time – temperature history inside the sample during the cooling stage. The main purpose of this quench system is to evaluate the quench power of different quenchant at different conditions (type, temperature and agitation).A stainless steel sample was used with a suitable measurement as a probe in designing this quench system.The performance of two of quenchants (water and brine) with different conditions was investigated, and the designed probe was used to illustrate the effect of quenching parameters (quenchant type, temperature and its agitation) on cooling curves and cooling rate.The quenching system has proven its ability to work effectively and the results showed that heat transfer properties were significantly affected by quenchant parameters.
Experiments were conducted to study the effect of quenching medium carbon steel in water-based MWCNTs nanofluids at 0.05 % wt. concentration quenchant, a large cylindrical sample with 46 mm diameter and 40 mm length made from medium carbon steel used with three K-type thermocouples with a diameter of 1.5 mm inserted in three locations for sample (center of the sample, mid-point between center and surface and 1 mm from the surface). A time-temperature reading data system was used to read temperature history during cooling stage.The same experiments were simulated using ANSYS Workbench with Thermal Transient Version 19, the cooling curves at three locations for the cylindrical steel sample calculated during quenching in MWCNTs nanofluids. Quench factor analysis was used to predict the hardness results from the calculated and measured cooling curves, and these results compared with the hardness test results conducted in the significant sample from the center to the surface. The results show excellent compatibility when compared between the hardness results from cooling curves, and it also shows a good agreement with the results of the hardness test, especially at the sample surface.
In the present work the effect of Corrosion & Scale Inhibitor was evaluated by using of the commercial product (Kurita S2050) that mainly containing of (Na2HPO4) sodium phosphate as corrosion inhibitor and (C6H11NaO7) sodium glocunate as scale inhibitor & dispersant. The dosing rate of this chemical was controlled according to the treatment system depend mainly on the monitoring of LI & RI indexes for (30) days treatment in the cooling tower unit of Al-Dora Oil refinery-Baghdad. The corrosion rate and the corrosion inhibitors efficiency were calculated by measurement of weight loss in standard test coupon (AISI 1010). After 30 day of the Field Test, the result show that the treatment program performance was effective in the corrosion & scale inhibition through an acceptable corrosion rate less than 0.018 in gmd. Also the result of corrosion rate was analyzed statistically by using of (ANN) to formulate a prediction equation to corrosion rate identification.
Due to the instability and irregular of national electric power supplied to residence sector in Iraq for long term history, attracted researchers interest to strive for solutions, and associated challenge dry and very hot summer season in Iraq on air conditioning application, A test room full size prototype was constructed in Baghdad, its size 33.5m3, the room is built from very good thermal insulation Autoclave Aerated Concrete AAC with white panted Concrete roof, test room is exposed to solar radiation during entire day, thermal energy shifted by time using thermal energy storage TES containing PCM, PCM is soft paraffin its phase inversion temperature (29 to 27)°C, thermal energy was shifted from night timing by cooling down TES (Discharging PCM) to peak time 11:00 am to 02:00 pm, the testes were carried out over entire summer season April to October, the results showed thermal energy can shift to by any quantity and time based on mass of PCM and enthalpy, electrical energy saved at peak time 52.5% of total power spent over season 2.7KW/day, Only 27% of electric energy utilized to discharge PCM during night, about 43% of heat lose is sourced from exposed roof, melting and solidification of PCM temperature must be within indoor comfort range 23 to 28 ?C to release or absorb the latent heat 41kJ/kg.
Desired mechanical properties like microstructure, micro hardness and wear resistance are the key parameters for which low carbon steel (AISI 1006) are widely selected. Surface heat treatment applied to improve these properties; traditionally surface heat treatments like induction hardening, in recent time’s laser surface hardening. In this work, thermochemical treatment (liquid nitriding) by using mixture from 61% NaCN, 15% K2CO3 and 24% KCL and followed by Nd:YAG laser surface treatment was done . The laser parameter were energy (0.89, 2, 4 and 9) J, spot diameter (0.790 ,0.33, 0.283 and 0.224) mm, pulses duration (1, 2.33, 4.47 and 9.87) ms with fix wavelength 1604nm. Laser surface treatment cycle was melting the layer surface, holding and rapid cooling in air medium. Optical microscopy (OM) and scanning electron microscope (SEM) has been used to study the microstructures and cross-sectional of molted and heat affected zones respectively. The wear test was done to measure the wear rate by using pin -on-disk principles were satisfied. The result shown that increasing in laser energy effects to increase in the area of melted and heat affected zones of nitriding steel. Also increasing in laser energy led to increase micro hardness about 61%, while wear rate decrease about 40 % and increased depth of molted zone.
The emission sources have great effects on our environment. Further using of fossil fuels because of our needs for heating purposes and developments leads to raising the emission concentration in the air which caused to health risks to human society and its environment. This paper deals with using a different percentage of Iraqi liquefied petroleum gas from 10% to 25% with different percentage of Iraqi Gas-oil fuel from 90% to 75%, keeping the thermal load constant in order to indicate the possibility of reducing the pollutant emissions . A dual fuel burner and equivalence ratio range from 0.8 to 1.4 is used to study the emission concentrations based on these equivalence ratio. For further reducing in emission and heat recovery from the exhaust gases the cooling effect also investigated for water mass flow-rate from 12 kg/s to 48 kg/s roughly. The results showed that for further increasing equivalence ratio the UHC, CO, and Soot increased by about 3% and NOx, and CO2 decreased by 2.5% and this due to decreasing the oxygen ratio in the mixture and incomplete combustion occurred. Also for increasing percentage participating of LPG fuel as a secondary fuel, UHC, CO, and Soot decreased by 8%and NOx and CO2 increased slightly. With heat recovery process the concentration of UHC, CO, and Soot increased slightly while NOx, CO2 decreased by 1.5% because of decreasing of combustion chamber temperature.
Türkiye possesses abundant geothermal resources. It is ranked seventh globally for this particular energy resources and grade among the first 5 in utilizing geothermal and thermal springs for various purposes such as electricity generation, residential cooling and heating, greenhouse operations, desiccating processes, thermal recreation, therapeutic applications, mining, agricultural uses, and aquaculture. The government's endorsement from renewable power sources is fueling growing interest on this particular energy sector. This article provides a comprehensive analysis of geothermal energy in select locations of Türkiye, including an assessment of its potential and various applications. The study seeks to provide a valuable involvement to the future advancements of a geothermal technology on Türkiye.
Hydrogen fuel is a good alternative to fossil fuels. It can be produced using a clean energy without contaminated emissions. This work is concerned with experimental study on hydrogen production via solar energy. Hybrid photovoltaic thermal system (PV/T) is used to convert solar radiation to electrical and thermal energy. The electrical energy is used to analyze water into hydrogen and oxygen by using alkaline water electrolyzer with stainless steel electrodes. The absorbed thermal energy is used to heat circulating water inside the copper serpentine pipe fixed on the back surface of the PV panel. A perforated pipe connected on the upper edge of PV panel is used to spray a thin layer of water on the PV panel surface for auxiliary cooling and improve the generated electrical power. The hydrogen production system is tested at different temperature of electrolysis water (40, 45, 50, 55, 60)?C. The experimental results show that the PV module electrical efficiency is improved by (14.31)%. while the power generated was enhanced by (3.94 to 15.40)%. The maximum hydrogen production rate is 153.3 ml/min, the efficiency of the system is 20.88% and the total amount of hydrogen produced in one day is 220.752 liter.
The purpose of this research is to manufacture and test adjustable sockets for below-knee amputation. This article studies using the pnuematic–pads for adjustable sockets. The manufacturing of an adjustable socket with pneumatic pads goes through several stages: In the theoretical design of the adjustable socket, the suggested materials were studied for the pneumatic pads, tubes, and pneumatic pump which should be suitable for the suggested application. In the experimental work, using composite materials for manufacturing the socket consisting of perlon and resin to achieve the rigid shape and required flexibility for the prosthetic user with the pneumatic pads. After assembling the adjustable socket parts, the pneumatic pads, the pump and the tubes, the socket were tested for several times on the patient. In the last stage, the pressure between the socket and the residual limb was measured using F-socket, and it was found that the results were: anterior (160kPa), lateral (167kPa), posterior (153kPa) and medial (348kPa). By comparing these results with what was previously studied, the pressure between the socket and the residual limb is within the acceptable range. The design provides good suspension and more adaptability to the change in stump volume. A posative feedback was given by the patient who used the prosthetic patient for several days as a trial to measure its safety and comfortablty.
An investigation of thermal conductivity enhancement, melting and solidification processes of Phase Change Materials (PCMs) by using metal foams has been carried out. Two models have been used in the experiments, model I for measuring the effective thermal conductivity of metal foam embedded in paraffin wax, and model II used as a small scale thermal energy storage device with and without metal foam for investigating melting and solidification processes of the PCM under different cooling conditions (natural and forced convection). The theoretical investigation involves analytical solution of two models, the semi-infinite medium for calculating the thermal conductivity, and the thermal energy storage system TESS has been analyzed including several assumptions for determining the convective heat transfer coefficient and the factors that controlling forced convection and solidification of the PCM. The experimental results show that the thermal conductivity of wax with 10 PPI metal foam increased by (37-39) times that of pure wax. Effects of pore density (10 and 40 PPI), metal foam, and mass flow rate on solidification process have been studied and the effects of pore density and metal foam on the melting process have also been investigated. The present experimental results have been compared with the available previous studies and gave a good agreement.
This study aims to review flow-induced vibration one of the repercussions of vibrations is caused by fluid movement. In general, the investigation of the structure of the systems affects the efficiency of the components that construct those systems. This review examined the influence of generated vibrations and internal pressure on fluid transport pipes using theoretical calculations, practical tests, and numerical analysis to identify and test the dynamic behavior of static fluid transport pipes. The experimental study considered the natural frequencies caused by the fluid pressure effect under various stability situations. The flow of all liquids, such as oil, water, gas, air, and vapors, through the pipes, was tested, and the mathematical models were correctly adjusted. All empirical, theoretical, numerical, and analytical research agrees that several approaches exist to develop, modify, and improve these metrics. However, one factor affecting rheological measurements is vibration, which was addressed as needed in the middle of the 20th century due to major discoveries that damage could be rooted in vibration. Established on the determinations, they provided mathematical models paired with pressure and velocity measurements of moving fluids and the influence of produced or uninduced vibration. This study demonstrates that additional empirical investigations, particularly more detailed analytical methodologies, are urgently required to produce better findings.