×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerRutting is the most common distress that most Iraqi asphalt pavements suffer from it. Asphalt binders are modified by using additives and polymers to enhance their physical qualities and fulfill the performance demands. Polyphosphoric acid (PPA) has been used in many countries to enhance the physical and mechanical characteristics of asphalt binders and mixtures that can improve the performance of asphalt pavements. In this paper, evaluation of the Iraqi asphalt binder and mixtures performance by using three percentages of Polyphosphoric acid (PPA) (0.4, 0.8, and 1.2) percent by asphalt binder weight and added to (60-70) penetration grade asphalt binder to show the applicability and suitability of using PPA in asphalt pavement in Iraq. Original asphalt binder and modified are subjected to traditional tests which are penetration, ductility, softening point, and viscosity. Results show better performance and enhancement of the physical properties of the modified binder. Other tests are Marshall Stability and wheel track tests. The results of the addition of PPA to the asphalt mixture show increases in the Marshall Stability and enhance the performance of the asphalt pavement mixtures. The wheel track test is applied to the original and modified mixture at two test temperatures 40 ?C and 50 ?C and the results show a decrease in the rut depth when the percentages of PPA increase. It is concluded that %PPA addition will enhance the performance of the Iraqi asphalt pavement and the mixture will be more rutting resistant, especially in high-temperature weather.
The objective of this paper is find the effect of using iron oxide as a filler on the Marshall stability, flow and the volumetric properties of HMA and compared the results with conventional HMA using limestone dust. Three blends were used: coarse, mid and fine with neat bitumen (AC 40-50). One aggregate type (crushed) with two types of fillers: limestone and iron oxide III (?- ) with three different filler content 6%, 8% and 10%. The Marshall mix design was conducted on the three blends and the optimum binder content is computed for each blend. The Marshall stability test results and the volumetric properties analysis showed that increasing the iron oxide content from 6% to 10% increases the stability about 28%, 17% , 16% for the coarse , mid and fine mixtures respectively. This increment in stability of mixtures using iron oxide related to the increment in specific gravity of the mix (Gmb) by (1.3% to 1.5% about 30 to 50 kg/m3). On the other hand, the flow of mixtures is decreased about (5%) for mixes using iron oxide than the ones that used limestone as filler. The fine blend with 10% iron oxide exhibit the highest stability of 13.3 kN. While the coarse blend stability was 10 kN for the same filler type and content. Generally, the Marshall Test results of HMA using iron oxide as filler showed better resistance to plastic deformation, also produce denser HMA with higher stiffness. On the other hand, the volumetric properties analysis showed lesser values as compared with conventional mixture where the void in mineral aggregates and void filled with asphalt has decreased but within the acceptable limits.
Open graded asphalt mixture is becoming more widespread where it is applied for various purposes, e.g. drainage of rainwater effectivity, traffic safety (high skid resistance), and controlling pollution noise. However, it has many other disadvantages, of which low stability, high stripping, and moisture sensitivity. The research aims to study the effect of styrene butadiene styrene SBS addition on the volumetric and mechanical properties of open graded mixture. In this research one type of aggregate with gradation (12.5 mm NMAS), asphalt of penetration grade (40/50), and cement as filler were used. Optimum asphalt content was selected based on the criteria of air voids content, asphalt drain down, permeability, and abrasion resistance (for aged and un-aged) samples. Other properties of open-graded mixtures, such as indirect tensile strength (ITS), moisture susceptibility, Marshall stability and flow were evaluated. The results show that addition of polymer (SBS) leads to an enhancement in the properties of the modified mixtures. There is an improvement in Marshall parameters. Also, a slight decreasing is noticed for permeability and air voids. For Cantabro abrasion loss (aging and un-aging condition), the abrasion resistance is increased, the drain down of asphalt is decreased from original mixture by addition of SBS. Finally, the moisture sensitivity is improved indicating that modified mixes becomes more resistant to water damage.
Hot mix asphalt embedded on "Reclaimed asphalt pavement"(RAP) has the advantages of high technology. Moisture damage is a concern in these mixtures at all service temperatures. Therefore, the performance of this mixture against moisture at all service temperatures was considered a target of this research study. In this way, the effects of humidity on the performance of varieties were investigated using experimental methods including tensile strength ratio (TSR). In the framework of this study, Four different ratios of RAP for each of the surface and bonding layers (10%, 15%, 20%, 25%) and (30,40,50,60)% were added to the hot asphalt mix (HMA) for the two layers respectively to study and find the content Optimal RAP for both layers RAP through Marshall stability and hygroscopic resistance of asphalt mixtures through moisture damage is examined. The ratio (TSR) of the mixtures containing the optimal RAP content is compared with the asphalt mixture without RAP for three fillers and for both layers. The results showed a slight decrease in the tensile strength of the (HMA) that does not contain RAP compared to the asphalt control mixtures containing the reclaimed pavement, where it was found that the percentages were slightly higher and still higher than 80%. The results indicate that in general, Although there are old materials in the hot asphalt mix (HMA) produced from RAP, which include aggregates and bitumen binder surrounding the aggregate particles, the performance of these mixtures and integrations against moisture damage. Because it contains this, it can have results with “hot asphalt mixtures” containing RAP for areas with damage without worry in addition to good natural curbs.