×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerMagnesium oxide nanoparticles were deposited by laser pyrolysis process. Three types of lasers were employed CW CO2, Q-switched Nd-YAG (short pulses) and long pulses Nd-YAG lasers. The size and density of nanoparticles vary with laser energy, power, pulse duration and the scanning speed of the laser. In this method, MgO nanoparticles were deposited by a laser beam on a quartz substrate from aqueous solution of magnesium nitrate. AFM images reveal formation of small nanoparticle size of 24.5 nm with surface roughness 6.97nm by Q-switched Nd-YAG laser (10 ns) when the energy was 1J. While for CO2 laser, the smallest size was 18.8 nm at 0.4mm/s scanning speed with surface roughness 5.21nm at the same scanning speed. Moreover, long Nd-YAG pulses laser produces relatively larger average size of 37.5nm at 0.8ms pulse duration. The absorption spectra from UV-Visible spectroscopy were also conducted. The best absorption intensity was obtained at a wavelength ranging between 420-430 nm for both lasers. Finally, Thermal analysis using COMSOL Multiphysics software for the deposition process reveals that maximum temperature about 440Kfor Q-Switched Nd-YAG laser at 1J laser energy. While for RF CO2 laser, the maximum temperature obtained at 0.4mm/s scanning speed is 850K.This work provides a good knowledge for the deposition of nanoparticles using laser beams.
Two lasers were utilized for silicon processing using photoelectrochemical etching and laser texturing in order to produce nano/micro structures, respectively. Photoelectrochemical etching process utilizes a CW diode laser of 532 nm wavelength was used to support electrochemical etching for both n-type and p-type conductivity. While laser texturing process was employed using pulsed fiber laser of 1064 nm wavelength. Various characterization methods were devoted to examine silicon micro/nanostructures surfaces produced by lasers. These methods include AFM, SEM and Raman scattering to provide clear evidence about formation of micro/nanostructures abundant at silicon surfaces. Moreover, FTIR analysis for the laser produced silicon surfaces could emphasize whether the resultant silicon surface is hydrophilic or hydrophobic. Image analysis software adopted a side view micro image was used to measure the contact angle between the water droplet and silicon micro/nano-surfaces. It is found that the laser produced silicon nanostructure by photoelectrochemical etching creates a hydrophobic surface and even super hydrophobic with contact angle of 130 degrees for 50 nm average size. In addition, utilizing fiber laser of high repetition rate for laser texturing produces microstructures that are super hydrophilic with contact angle could reach 8 degrees for a surface dimension of 50 μm.
Porous Silicon (PSi) samples with (100) orientation n-type were prepared by photo-electrochemical etching process for different variable parameters and fixed electrolyte solution HF:C2H5OH:H2O (2:3:3). Physical and optical properties of PSi would be varied with the variation of process parameters such as current density, anodization time and laser wavelengths. Two types of 50 mW diode lasers were chosen, 473 nm Blue & 532 nm green at 20 mA/cm2 & 15 min etching time to assist the iodization process. The band gap of the fabricated layer has raised up to (2.9 eV) which is more than twice its original value for the c-Si (1.12 eV). _x000D_ Exploiting the obtained gap energy values, the refractive index of porous silicon layer was calculated depending upon Vandamme empirical relation. It was observed that the porosity is modifiable through etching conditions, which in turn makes refractive index also modifiable. Thus, the calculation depended on taking certain parameters as the current density and etching time in order to compare the effect of applying the two laser wavelengths. AFM was applied to observe the homogeneity and roughness of the PSi mono-layer. The results are in a very good agreement with the range of the refractive indices of PSi and the illumination with green laser gives a better conclusion to use in solar cells as a good absorber and a bad reflector.
The aim of this work is to use Fiber Bragg Grating (FBG) to detect the breast cancer at its earliest stages based on the Photoacoustic (PA) hybrid technique. The fiber Bragg gratings sensitivity to acoustic wave, effect of grating length, effect of grating refractive index modification, and ultrasonic frequency on the wavelength sensitivity and intensity sensitivity of the ultrasonic sensor (FBG) for ultrasonic waves were investigated using a simulation programs. A wavelength for the photoacoustic (PA) excitation laser was chosen with respect to a high absorption by the tumor and with low absorption to the surrounding tissue (normal tissue); for higher contrast absorption between them. Fiber Bragg can be used as a sensor to detect the acoustic wave emitted from the tumor (depending on the photoacoustic principle). In this study, k-wave a MATLAB toolbox was used to simulate photoacoustic wave which is detected with fiber Bragg grating simulation, using Optisystem program. The acoustic wave was transferred to FBG by using Optisystem-MTLAB communication programs to detect tumors.
Surface reconstruction of silicon using lasers could be utilized to produce silicon nanostructures of various features. Electrochemical and photoelectrochemical etching processes of silicon were employed to synthesize nanostructured surface. Effects of current densities 5, 10 and 20 mA/cm2 on the surface features were examined. It is found that the surface porosity and layer thickness increase with the current density. Moreover, large surface area of 410 m2/cm3 can be achieved when laser power density 0f 0.6 W/cm2 was used during the etching process. Optimum operating conditions were found to achieve better silicon nanostructured surface features. The surface roughness can be reduced to 8.3 nm using laser beam of 650 nm irradiated the silicon surface during the photoelectrochemical etching process. The surface morphology of the nanostructured silicon surface using SEM and AFM could give rich details about the surface. Silver nanoparticles of 10 – 20 nm was embedded at the nanostructured silicon surface by LIFT process to reduce the surface resistance and maintain the large surface area. This technique enables silicon nanostructures to be efficiently used in many optoelectronic applications.
In our work, three internal regions of rat are exposed to four different lasers with different power density, and then studying the histology of the tissues. Together the total absorption and transmission of the tissues at certain wavelength were determined.Changing the wavelength across the absorption peak caused a significant difference in laser tissue interactions and changing the absorption coefficient, relaxation time, generated heat, and the intensity as a function of penetration depth. Furthermore, little mechanical damage could be seen in conventional histology.