×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerESAR feet are prosthetic feet with carbon fiber parts that store mechanical energy while standing and release it during propulsion. It is believed to reduce the metabolic energy needed for walking, and to promote the economy of walking. However, there is little scientific evidence to support this claim. This study aimed to compare the energy storage properties of two prosthetic feet made of carbon fiber using the P-Walk, G-Walk, and Podium devices developed for gait analysis, which is a systematic examination of human movement, enabling phasing, estimation of musculoskeletal performance, and determination of kinematic and motor parameters. The amount of energy was calculated for each of the feet using the load deflection test, and the results showed that the new artificial foot with an energy of 6.186 joules showed a great improvement in the results of the tests compared to the old artificial foot with an energy of 3.403 joules. The Podium device tests showed a significant improvement in walking patterns and pressure distribution after using a new foot. The pressure distribution became almost equal on both sides, and the angular deviation of COP decreased from -7 to 1.3 degrees. Ground reaction force vector tilt results also improved, with a body angle of 0 degrees and inclination varying slightly depending on the tibiofemoral angle for males. P-Walk results reveal left-sided static test pressure distribution, exposing amputees to osteoarthritis risk and revealing lack of confidence in prosthetic foot. After use the new prosthetic foot, amputees press more on right foot, indicating balance restoration. The G-Walk device shows the effectiveness of both healthy left and prosthetic foot when walking on an amputated right leg when use the new prosthetic foot. The amputated side's performance is similar to a healthy limb, with minimal difference and within normal limits. Walking cadence and speed values are within normal ranges, while stride length and step length are outside normal ranges for both sides. Obliquity results show a small difference in pelvic angles due to weak pelvic muscles, but these are close to standard values for prosthetic foot use. The amputee's opinions about the evaluation of the new prosthetic foot were good when using the T-score by 61.0 with a rate of 86.4%. It was a significant improvement compared to the old foot with an evaluation of 53.6 by 63.9%.
In this work, nine types of laminated composite materials used for experimental study to investigate the tensile and fatigue properties of partial foot prosthetic socket which fabricated by using vacuum pressure system . The composite material matrix were Lamination 80:20and reinforced with nine types of laminations (perlon, n-glass, fiber glass and carbon) by variation of thickness according to lamination. Results show that the mechanical properties were improved by increasing the two layers of carbon fiber, fiber glass and n-glass layers instead of zero layer with six layers of perlon lead to the increased in(yield strength ?y, ultimate tensile strength ?ult and modules of elasticity E with (71% ,76% and 58%) respectively for carbon fiber, (20% , 19% and 40%) for fiber glass and ( 22% , 5.5% and 29% ) for n-glass. Results show that (3perlon+2carbon fiber+3perlon) gives the best value of mechanical properties and has higher Endurance limit stresses (?e) which increase lifetime for the patient . It is recommend to use this type of lamination for the layup partial foot prosthetic socket because it meets the demand lamination layers for acceptable mechanical properties and its minimizing the cost of socket lamination to suitable costing value.
This article is about studying the placing direction effect of a piezoelectric sensor on the shoe insole in the GRF results. Where the sensors used in this research are in two directions, along and perpendicular to the foot midline. In the both cases the sensors were fixed on the shoe insole to sense the foot pressure. For the first set of sensors which are perpendicular to the foot midline the collected data has similar trend to the GRF collected from the force plate, as the small lateral strain in the shoe insole due to the patient weight and GRF is close to the GRF data collected from other measurement system. On the other hand, the collected data from the second set of sensors which are in a longitudinal direction with the foot midline will have different trend and values from the collected data from the force plate or any other GRF measurement system. This different in the results is due to the large longitudinal strain in the shoe insole due to the patient weight which produce dissimilar results from the force plate result data.
There are many patients who face a lot of things that hurt the knee joint. Knee replacement is the best solution to these problems. This research was based on reducing the vibrations of daily activities as measured by the frequency of foot and knee for the patient for three cases when the bare foot, sports shoes with ground air and sports shoes with ground air with silicon damping. Patient information for this work was of age, weight, height and leg length 48 years, 90 kg, 160 cm, 84 cm, respectively. The results was shown that the decline in acceleration results was in the case of sport shoes with ground air with silicon damping with 22.57%, while the decline in vibration results was in the case of sports shoes with ground air with -54.9%.
One of the health issues that many people encounter on a daily basis is bone fracture, which can happen for a number of reasons, such as arthritis, sprains, or external trauma . The patient experiences instability as a result of these issues . Internal fixation is a type of surgery used to support and mend a damaged bone Treatment options include ankle joint fixation, a surgical procedure employing pins, plates, rods, or screws. This study uses gait analysis methods to assess lower limb biomechanics . Gait analysis is vital for understanding walking patterns and intervention effectiveness. The impact of different shoe designs on ankle mechanics, using the finite element method and ANSYS, is investigated The results of the EMG and the GRF were discussed._x000D_ This research deepens our understanding of lower limb biomechanics and ankle joint health. By evaluating stress effects and designing custom shoes, it enhances ankle injury treatment and management strategies._x000D_ The patient, a 70-year-old woman with an internal fixation on her ankle joint, underwent a CT scan of her ankle. The patient underwent a number of experiments to evaluate her stability. EMG was used to determine the muscle stress for a brief period of time, and ground reaction force was then used to determine the pressure of walking. Both EMG and GRF have two walking speeds of1.5and 2 km/h while wearing four different types of shoes. The behavior of the EMG demonstrates that the stress on the muscle increases as walking speed increases, and the results varies depending on the shoe. The patient is afraid to apply pressure to the injured foot, so the health foot has better pressure over the entire foot_x000D_
In this study, an experimental comparison has been made between the traditional plastic materials (Polypropylene and Polyethylene) and selected composite materials (Perlon-Carbon-Perlon and Hybrid Carbon fiber-Glass fiber) to manufacture a long life Partial Foot Prosthesis. To improve the mechanical properties, increase the lifetime of the prosthesis, and reduce the cost to the patient, two types of composite materials were used and compared with plastic materials. Samples were manufactured and tested with different test methods (Tensile, flexural, and fatigue test). All tests were performed at room temperature.The results showed that the composite materials achieve a large increment in mechanical properties such as (?y, ?ult, E, ?b, and Ef) whichwere increased to a percentage of (200% - 261%),(330% - 243%), (295% - 203%), (276% - 270%),and (413% - 301%) in Perlon-Carbon-Perlonlamination as compared with Polypropylene andPolyethylene respectively. However theincreasing percentage in Hybrid Carbon fiber-Glass fiber was (353% - 270%), (470% - 347%),(388% - 267%), (203% - 199%), and (244% -178%) as compared with Polypropylene andPolyethylene. At the same time, the fatigue lifewas sharply increased in both of the Perlon-Carbon-Perlon and Hybrid Carbon fiber-Glassfiber.
In this research the behavior of cylindrical shells under axial load have been studied. The experimental program is included two groups: the first consists of nine cylinders; each has a diameter of 150 mm, while the height varies from 100 to 500 mm and thickness of 1.5 mm, test results show that the optimum height to achieve the maximum strength is 300 mm with L/D equal to 2. The second group consists of two cylinders with diameter of 150 mm and height of 300 and 500 mm strengthened with stiffeners plate welding from inside at four quarters with thickness of 1.5 mm and width 20 mm fabricated from the same metal of the cylinders. After testing these two cylinders were gain an increase in the strength reached to 42% for 300 mm cylinder and 26.4% for 500 mm cylinder. The failure modes for these two groups are: the buckling at bottom like “elephant’s foot” for cylinders height from 100 to 300 mm and “inelastic buckling” for cylinders height from 350 to 500 mm for the first group, and the ” inelastic buckling” for the second group.
Orthoses and prostheses were Chosen and laminated based on their high Yield, ultimate stresses, bending stresses, and fatigue limit. Response Surface Methodology (RSM) was utilized to find the best values for two parameters reinforcement perlon fiber and percent of Titanium Nanoparticle coupled with the matrix resin during optimization. The response surface methodology combined the expertise of mathematicians and statisticians to construct and analyze experimental models. Using this method, we identified 13 different lamination samples comprising a wide range of perlon number and Ti nano Wt% in their Perlon layer composition. All lamination materials defined by RSM methods and produced by a vacuum system were subjected to a battery of tests, with fatigue tests performed on the ideal laminating material in contrast to laminations created in the first study (Tensile test, Bending test, and Fatigue tests according to the ASTM D638 and D790 respectively). In comparison to the other 12 laminations tested using Design Expert version 10.0.2, the lamination with ten perlon layers and 0.75 percent Ti nano proved to be the strongest overall in terms of Yield, ultimate, and bending loads. This study used composite materials and titanium nanoparticles to characterize and fabricate ankle foot orthoses. Strength in bending should amount to about 70 MPa, around 85 MPa in tensile tension. Two empirical quadratic equations for the models of peak bending strength and maximum tensile stress with 95% confidence were created using the response surface approach and analysis of variance within the design of experiments software.
With the occurrence of pathological disorders in some people or aging, metabolic energy consumption begins significantly due to the weakness of the peripheral muscles and the increase in body fat with time, which aggravates the issues for this type of people, causing the rest hours extremely lengthy and consequently may produce heart or arterial diseases and elevate the mortality rate. Regarding the significance of the matter, this study examines a number of previous researches that featured several approaches to energy calculation and strategies for lowering energy consumption through the use of various external assistance devices, such as exosuits or exoskeletons, to assist people in carrying out their everyday tasks. And additionally discussed musculoskeletal simulation employs a variety of programs, especially OpenSim, which enables users to build models of musculoskeletal structures and produce dynamic movement simulations. According to the research findings, exoskeletons and other assistive technology can successfully lower the cost of metabolic energy to varying extents, depending on the device's weight, placement within the body, and whether it is active, semi-active, or inactive. In the future, the work to design and simulate a semi-active torsional ankle-foot exoskeleton with a specialized mechanism aimed to minimize metabolic energy.