×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial ManagerRutting is the most common distress that most Iraqi asphalt pavements suffer from it. Asphalt binders are modified by using additives and polymers to enhance their physical qualities and fulfill the performance demands. Polyphosphoric acid (PPA) has been used in many countries to enhance the physical and mechanical characteristics of asphalt binders and mixtures that can improve the performance of asphalt pavements. In this paper, evaluation of the Iraqi asphalt binder and mixtures performance by using three percentages of Polyphosphoric acid (PPA) (0.4, 0.8, and 1.2) percent by asphalt binder weight and added to (60-70) penetration grade asphalt binder to show the applicability and suitability of using PPA in asphalt pavement in Iraq. Original asphalt binder and modified are subjected to traditional tests which are penetration, ductility, softening point, and viscosity. Results show better performance and enhancement of the physical properties of the modified binder. Other tests are Marshall Stability and wheel track tests. The results of the addition of PPA to the asphalt mixture show increases in the Marshall Stability and enhance the performance of the asphalt pavement mixtures. The wheel track test is applied to the original and modified mixture at two test temperatures 40 ?C and 50 ?C and the results show a decrease in the rut depth when the percentages of PPA increase. It is concluded that %PPA addition will enhance the performance of the Iraqi asphalt pavement and the mixture will be more rutting resistant, especially in high-temperature weather.
Open-graded-fraction-course (OGFC), is a hot asphalt mixture usually utilized as a private purpose wearing course, because of open graded asphalt mixture and aggregates skeleton (stone-on-stone) contact, it contain a relatively high air voids’ percentage, after compaction which are permeable to water. In this research one type of gradation was used (12.5 mm) NMAS, to preparing the OGFC asphalt mixtures, penetration grade 40/50, crushed aggregate, asphalt content prepared with 4 % and up to 6 % by weight of mixture with 0.5 % increments. Optimum asphalt content (OAC) was selected based on these criteria, air voids content, asphalt draindown, permeability, and abrasion resistance (aged and un-aged) condition. The mix performance had been investigated by indirect tensile strength and moisture susceptibility (sensitivity) measured according to the (AASHTO T283-14). Results illustrate that the increasing of asphalt binder content leads to a decrease of the air voids content, abrasion loss and permeability values, while draindown increase, conversely, the indirect tensile strength (ITS) had been significantly increased for both conditions and this is a gaod suggestion to resistance alongside moisture susceptibility. It can be decided that the increasing of asphalt binder percent in OGFC asphalt mixture, leads to an increase in the thickness of binder coating around the aggregates. On the other hand, the influence of modifier that prepared with 4% styrene-butadiene-styrene (SBS) on OGFC asphalt mixture tends to improve the mix properties and exhibit higher (TSR) as compared with original asphalt by (31, 27.7 and 24.4) % at asphalt percent (4.8, 5.3 and 5.8) %, respectively. The SBS improved the adhesion between aggregate and asphalt which leads to reduce stripping of HMA, horizontal deformation, and increased the tensile stiffness modulus value.
Improving the ability of asphalt pavement to survive the heavily repeated axle loads and weathering challenges in Iraq has been the subject of research for many years. The critical need for such data in the design and construction of more durable flexible pavement in bridge deck material is paramount. One of new possible steps is the epoxy asphalt concrete, which is classified as a superior asphalt concrete in roads and greatly imparts the level of design and construction. This paper describes a study on 40-50 penetration graded asphalt cement mixed with epoxy to produce asphalt concrete mixtures. The tests carried out are the Marshall properties, permanent deformation, flexural fatigue cracking and moisture damage. Epoxy asphalt mixes performed better on resistance to fatigue and permanent deformation. They also performed significantly better on low-temperature properties and resistance to moisture damage. The addition of 30 percent of epoxy (by weight of asphalt cement) resulted in increase of Marshall stability by 39.8 percent, improve the tensile strength ratio by 22.9 percent, lowering both the rate of permanent deformation by 26.8 percent and the fatigue accumulation coefficient by 53.5 percent, in comparison with control HMA. Based on the above findings, it is recommended to use epoxy asphalt mixes as an optimal material for paving bridges deck in Iraq since it showed good prospects for this application due to the valuable performance and durability improvement.
Chemical additives and polymeric materials, selected for their compatibility and ability to improve asphalt's performance in demanding environments. Key additives, including Polyphosphoric Acid (PPA), Polyvinyl Acetate (PVAC) beads, Maleic Anhydride (MA), and Ethylene Vinyl Acetate (EVA) resin, were mixed in precise ratios with the asphalt binder. These additives were chosen to evaluate their effects on crucial performance indicators, such as the Penetration Index (PI) and activation energy, which measure the material’s thermal stability, flexibility, and resistance to deformation. Results demonstrated that the addition of these materials significantly increased the asphalt’s activation energy by up to 45.44%, enhancing its resistance to temperature fluctuations and providing better stability under various environmental stresses. The Penetration Index (PI) also improved notably, indicating that modified asphalt exhibits greater durability and reduced susceptibility to cracking or deformation under thermal changes. These enhancements contribute to lower road maintenance requirements and support greater energy efficiency in asphalt production and application processes. Compared to neat asphalt, the modified asphalt exhibited superior thermal stability, mechanical resilience, and overall performance, making it suitable for use in diverse climatic conditions. This study provides valuable insights into sustainable asphalt modification techniques, emphasizing the role of polymer and chemical additives in extending pavement lifespan and reducing environmental impact through improved material properties.
Hot mix asphalt embedded on "Reclaimed asphalt pavement"(RAP) has the advantages of high technology. Moisture damage is a concern in these mixtures at all service temperatures. Therefore, the performance of this mixture against moisture at all service temperatures was considered a target of this research study. In this way, the effects of humidity on the performance of varieties were investigated using experimental methods including tensile strength ratio (TSR). In the framework of this study, Four different ratios of RAP for each of the surface and bonding layers (10%, 15%, 20%, 25%) and (30,40,50,60)% were added to the hot asphalt mix (HMA) for the two layers respectively to study and find the content Optimal RAP for both layers RAP through Marshall stability and hygroscopic resistance of asphalt mixtures through moisture damage is examined. The ratio (TSR) of the mixtures containing the optimal RAP content is compared with the asphalt mixture without RAP for three fillers and for both layers. The results showed a slight decrease in the tensile strength of the (HMA) that does not contain RAP compared to the asphalt control mixtures containing the reclaimed pavement, where it was found that the percentages were slightly higher and still higher than 80%. The results indicate that in general, Although there are old materials in the hot asphalt mix (HMA) produced from RAP, which include aggregates and bitumen binder surrounding the aggregate particles, the performance of these mixtures and integrations against moisture damage. Because it contains this, it can have results with “hot asphalt mixtures” containing RAP for areas with damage without worry in addition to good natural curbs.
Rutting is considered as the most generated distress in Iraqi roads as a result of the high temperature and excessive traffic load. So, it is essential to utilize polymer modified binder to increase the performance of pavements. The objective of this paper is to assess the effect of aggregate gradation and filler content on the rutting formation of Colored Hot Mix Asphalt CHMA. The HMA was colored by using iron oxide as filler to produce red HMA. Two blends were used: fine and coarse with two different types of filler iron oxide for CHMA and limestone for conventional HMA with two filler content 6% and 10%. Neat (AC 40-50) and modified asphalt (AC 40-50 + 4%SBS) were used. Tests are held on adding 4% Styrene Butadiene Styrene )SBS( by the weight of neat asphalt (AC 40-50) to raise the performance grade by two grades from PG (64-16) to PG (76-16) [1] and [2]. The wheel tracking test is used to assess the rut depth of the CHMA. The test results showed that the using iron oxide with neat asphalt increase the rut depth resistance by 200 and 400 failure load cycles than mixtures using limestone (cycles that mix reach 25 mm rut depth) for fine and coarse mix respectively. Also, the effect of gradation shows that the fine mixture fails at 4000 cycles while the coarse mixture fails at 1800 cycles for 6% limestone mixtures. Increasing the iron oxide content from 6% to 10% leads to increase the failure load cycles by 2200 and 1200 cycles for fine and coarse mixture respectively using modified asphalt. The fine mixture with 10% iron oxide using modified asphalt gives the best performance with 7000 cycles than the coarse mixture with 10% filler content and modified asphalt with 4000 cycles. irrespective the filler and type of binder, the dense mixtures using iron oxide as filler exhibit better resistance to rutting formation than coarse mixtures.
Reflective cracking is a serious issue that Adversely influences the performance and longevity of asphalt overlays over deteriorated pavements. This review Looks for the Technologies which used to reduce the reflection cracks propagation by insert a new Strategies and different design materials. This research dealt with many treatments such as: increasing the layer thickness of Hot Mix Asphalt (HMA), creating modified asphalt by adding polymers to asphalt, rubberizing asphalt, carbon black, sulfur and other different materials. Geosynthetic materials were studied and analyzed to evaluate their ability to increase the layer tensile strength and minimize the effect of reflection cracks such as geotextiles, geogrids, and Stress Absorbing Membrane Interlayers (SAMI). The research shows that the increasing of overlay asphalt layer thickness leads to durability development. On the other hand, using developed materials like Polymer-Modified Asphalt and Stress Absorbing Membrane Interlayers (SAMI) Strategies leads to increasing the service life of the repaired pavement. The conclusion indicated that the development of overlay asphalt layer thickness and layer reinforcement and applying advanced environmental systems can be improving the pavement performance. These Strategies can produce a perfect solution to prevent or reduce the reflection cracks in rigid and flexible pavement.
Utilization of additives can be an effective way to improve the durability and performance of HMA, making them more resistant to Moisture and deformation. Plus, they can reduce the need for maintenance and repairs, saving you time and money in the long run. In this study, CKD was used in place of limestone as a filler in the asphalt mixture in proportions of 0%, 25%, 50%, 75%, and 100%, and polymer SBS 4%by weight of asphalt. According to the findings, replacement-content CKD had the highest asphalt content. When the CKD is between 25% and 50%, Stability, Flow, and Indirect Tensile Strength are improved, while the density of the asphalt mixture decreases and the amount of air voids increases at higher ratios. While SBS leads to an increase in the hardness of the adhesives. As a consequence, the stability of the SBS-containing mixes resulted in higher values than the control and additive-containing mixtures (CKD), as well as a decrease in the number of air voids. According to the results, CKD should not constitute more than half of the filler weight in the asphalt mixture.
The objective of this study is determining the mixing and compaction temperature of the modified asphalt mixture. Results of binder tests showed that the addition of 3% SBS to control asphalt (PG 64-16) would achieve the desired performance level (PG 76-16) a performance grade that fits our climate with traffic loads. When using 5% SBS the performance grade of binder increased three grades (PG 82-16) and when increasing SBS content to 8% the performance grade increased four grades (PG 88-16). At shear rate of 500 (s-1), the modified asphalt viscosity can be obtained at different temperatures and the viscosity temperature curve can be achieved. As a result, the mixing and compaction temperature of modified asphalt can be determined to reach 0.17 ± 0.02 Pa.s and 0.28 ± 0.03 Pa.s for mixing and compaction, respectively. It is noted that SBS modified reached a viscosity of 3 Pa.s when 8 % additive. Additive contents above these values may not be suitable for good workability and pump ability according to Superpave specifications. While addition of 5% SBS with control asphalt, more than 3.7times at 135°C Increase the viscosity. Marshall Stability test indicated that the strength for the SBS specimens increases as compared to the conventional specimens. An increase of about 39%, 74%, 102%, was observed with 3%SBS 5%SBS 8%SBS modified binders, respectively. The Marshall test results for 8%SBS binders required compaction temperatures above 175°C need to keep up quality of HMA item while limiting natural effect amid development, these proposals are unsatisfactory Modified mixtures the 5% SBS modification was determined to be the maximum useful content. The Superpave method to estimate mixing and compaction temperatures show are not practical for use with modified binders. Also, it is observed that good agreement values between the average Marshall compaction temperature and the High Shear Viscosity Method (HSRV) and lower than Superpave methods Where the decline ranges from 15 ºC to 17 ºC.
Reclaimed (recycled) asphalt pavement (RAP), the most recycled material worldwide, is the mostly reclaimed material utilized in hot mix asphalt. Polymer (Crumb rubber) incorporation frequently leads to enhanced durability and resistance to heat cracking and rutting, two forms of permanent deformation. It also relieves stiffness and minimizes fatigue damage. This study aims to gather all previous RAP-related research and crumb rubber CR, so that the impact of using these materials on mechanical, physical properties of asphalt pavement, environmental effect and cost effective are clarify and explained. The finding of this research proved that the use of RAP and CR provide considerable structural and financial enhancements to the construction.
Open graded asphalt mixture is becoming more widespread where it is applied for various purposes, e.g. drainage of rainwater effectivity, traffic safety (high skid resistance), and controlling pollution noise. However, it has many other disadvantages, of which low stability, high stripping, and moisture sensitivity. The research aims to study the effect of styrene butadiene styrene SBS addition on the volumetric and mechanical properties of open graded mixture. In this research one type of aggregate with gradation (12.5 mm NMAS), asphalt of penetration grade (40/50), and cement as filler were used. Optimum asphalt content was selected based on the criteria of air voids content, asphalt drain down, permeability, and abrasion resistance (for aged and un-aged) samples. Other properties of open-graded mixtures, such as indirect tensile strength (ITS), moisture susceptibility, Marshall stability and flow were evaluated. The results show that addition of polymer (SBS) leads to an enhancement in the properties of the modified mixtures. There is an improvement in Marshall parameters. Also, a slight decreasing is noticed for permeability and air voids. For Cantabro abrasion loss (aging and un-aging condition), the abrasion resistance is increased, the drain down of asphalt is decreased from original mixture by addition of SBS. Finally, the moisture sensitivity is improved indicating that modified mixes becomes more resistant to water damage.
This paper focused on evaluating the effect of aggregate gradation and polymer modification on indirect tensile strength (ITS) and the static stiffness for hot asphalt mixtures. In particular, data from ITS tests have been processed to obtain stiffness measurements through the application of Hondros theory. The results showed that fine mixtures had a better tensile strength by 26.3% than the coarse mixtures. The effect of compaction also was examined, the results showed that samples compacted with the Superpave gyratory compactor (SGC) had an enhancement in ITS by 36.58 and 23.1% in comparison with Marshall and roller compactor respectively. Polymer modifiers were used to estimate their effect on tensile strength, adding 4, 6, and 8% of Styrene-Butadiene-Styrene (SBS), which can rise the ITS by 3.2,6.14 and 13.3% of the non-modified asphalt mixture. Furthermore, using 4, 6, and 8 percent of SBS could increase static stiffness by 53.9, 209.6, and 302.4% respectively for roller compacted fine mixes and 58, 220, and 379.3% for SGC compacted mixes. Furthermore, SBS raised the stiffness modulus by 52.3, 188, and 295% for Marshall compacted mixes. Using hybrid modifier can improve the stiffness of the asphalt mixture. However, The results indicate that using 1, 2 and 3% polyvinyl chloride (PVC) can magnify the stiffness of mixtures by 41.2, 199.8% and 262.6 for roller compacted mixtures and 133.4, 212.1 and 354% for SGC compacted mixtures, whereas there is a stringent increasing by 133.4, 189.2 and 354% for Marshall compacted mixes. Otherwise, polymer-modification can decrease the fracturing index for coarse and fine mixtures.
In Iraq some pavements of the newly constructed highway appear precocious distresses with unfavorable implications especially on the safety and the frugality. Cracking and permanent deformation are main types of these failures. The filler is doubtful to be a master contributor to these failures where its content has a significance effect on the mixture stiffness, and thereby affect the HMA pavement performance. The main objective of this research is to appreciate the influence of different contents of filler on the volumetric properties of asphaltic mixtures thus performance of asphalt mixtures through Comparative Evaluation between conventional Marshall Method and Super pave system. The implementation of a detailed experimental work is carried out to achieve the study objectives through the preparation of asphalt concrete samples using aggregate from Al-Nebaie quarry, (40-50) asphalt cement from Dourah refinery and limestone dust filler with four different contents of (0%, 4%, 8%, and 12%) by weight of the total aggregate. The volumetric properties for each mix design method are evaluated using Marshall Test and the Super pave Gyratory Compacter. The influence of filler contents on the rendering of these mixtures was evaluated.
Moisture-induced damage in asphalt pavements, is defined by adhesive failure at the binder-aggregate interface and decreased mechanical integrity, severely reduce pavement durability. The research examines the mechanical properties and moisture sensitivity of hot mix asphalt (HMA) enhanced with styrene-butadiene-styrene (SBS) polymer and including reclaimed asphalt pavement (RAP). Laboratory assessments, including indirect tensile strength (ITS) and tensile strength ratio (TSR) tests, were performed on conventional HMA, SBS-modified HMA (4% SBS), and SBS-modified HMA contained 20% RAP. The results indicated that SBS modification significantly improved mechanical and moisture resistance properties, where unconditioned ITS specimens increased by 37.1% and TSR value enhanced by 13.5%. The incorporation of RAP decreased ITS value by about 21 % relative to pure SBS-modified HMA; nevertheless, the SBS+RAP combination still show higher ITS and TSR values than conventional HMA.
A tack coat is a minimal coating of asphalt cement, cut-back asphalt, or asphalt emulsion to an existing pavement surface between layers to guarantee proper bonding between the two layers and longitudinal and transverse joints. Numerous researchers have assessed interlayer adhesion employing failure-mode behavior tests, such as pull-off, direct shear, and torsion testing. This study aims to quantify the best tensile resistance obtained using three types of cutback asphalt (RC70, RC800 modified with polymer 4.5% & MC70). All are applied on concrete surfaces at a rate of 0.5 L/m². The Proceq DYNA Z16 pull–off tester is used to measure the tensile strength at a rate of 0.25 kN/s. It is found that the average tensile strength of the tack coat materials is (0.319, 0.138, 0.028) MPa, respectively. It is concluded that RC70 has the maximum tensile strength. Also, the different types of solvent affect adhesion strengths; RC70 was Prepared using gasoline, while MC70 used petroleum. Gasoline has greater volatility and thus increased adhesion. Failure strength modes of interior bonding varied between cohesive failure adhesive and adhesive failure.
This study implements the soft computing techniques such as Artificial Neural Network (ANN) and an adaptive Neuro-Fuzzy (ANFIS) approach. Thus to model the rutting prediction with the aid of experimental uniaxial creep test results for asphalt mixtures. Marshall samples, having Maximum Nominal Size of 12.5 mm, have been selected from previous studies. These samples have been prepared and tested under different conditions. They were also subjected to different loading stress (0.034, 0.069, 0.103) MPa, and tested at various temperature (10, 20, 40, and 55) °C. The modeling analysis revealed that both approaches are powerful tools for modeling creep behavior of pavement mixture in terms of Root Mean Square Error and Correlation Coefficient. The best results are obtained with the ANFIS model.
The present investigation looked at whether the Bailey approach to aggregate gradation could be used to construct Superpave HMA blends. It also looked at how this approach influenced the rutting performance associated with these mixes and compared it to mixes of asphalt created by Superpave gradations. The current research included four aggregate gradations: both fine and coarse gradations for the Superpave and Bailey gradation procedures. The repeated loading test was utilized to assess the rutting performance. The findings indicated that temperature, stress level, and aggregate gradation all had a significant impact on rutting performance. In contrast to the other three gradations, the third mixture gradation exhibited the least amount of non-reversible deformation. It translates to pavement that is more resistant to rutting and less susceptible to it.
The objective of this paper is find the effect of using iron oxide as a filler on the Marshall stability, flow and the volumetric properties of HMA and compared the results with conventional HMA using limestone dust. Three blends were used: coarse, mid and fine with neat bitumen (AC 40-50). One aggregate type (crushed) with two types of fillers: limestone and iron oxide III (?- ) with three different filler content 6%, 8% and 10%. The Marshall mix design was conducted on the three blends and the optimum binder content is computed for each blend. The Marshall stability test results and the volumetric properties analysis showed that increasing the iron oxide content from 6% to 10% increases the stability about 28%, 17% , 16% for the coarse , mid and fine mixtures respectively. This increment in stability of mixtures using iron oxide related to the increment in specific gravity of the mix (Gmb) by (1.3% to 1.5% about 30 to 50 kg/m3). On the other hand, the flow of mixtures is decreased about (5%) for mixes using iron oxide than the ones that used limestone as filler. The fine blend with 10% iron oxide exhibit the highest stability of 13.3 kN. While the coarse blend stability was 10 kN for the same filler type and content. Generally, the Marshall Test results of HMA using iron oxide as filler showed better resistance to plastic deformation, also produce denser HMA with higher stiffness. On the other hand, the volumetric properties analysis showed lesser values as compared with conventional mixture where the void in mineral aggregates and void filled with asphalt has decreased but within the acceptable limits.
The main objective of this study is to design the asphalt pavement structure for the Alkut-Mayssan highway in Iraq as a case study by using PCASE application to determine the necessary thickness of CR-modified asphaltic layers. Additionally, Marshall tests were used to investigate the effect of the dry process crumb rubber modifier on the thickness of the binder coarse layer based on various variables, such as the crumb rubber modifier with different content (1, 2, 3, 4, 5)% and sizes (0.3mm, 2.36mm , 4.75mm, and mix gradation). The test results show that while pavement thickness reduced as crumb rubber gradation increases, MR values increase. Additionally, as compared to the control mixture, the addition of 1% of CR in various gradations could decrease the thickness of the asphalt binder layer.
This paper presents the design of robust four parameters (two degree of freedom) PI-PD controller based on Kharitonov theorem for antilock braking system. The Particle Swarm Optimization (PSO) method is used to tune the parameters of the proposed controller based on Kharitonov theorem to achieve the robustness over a wide range of system parameters change. The proposed cost function combines the time response specifications represented by the model reference and the frequency response specifications represented by gain margin and phase margin and the control signal specifications. The model reference control is used because of the antilock braking system is originally nonlinear and has different operating points. The robust stability is guaranteed by applying the Kharitonov theorem. Three types of road conditions (dry asphalt, gravel and icy) are used to test the proposed controller.