×
The submission system is temporarily under maintenance. Please send your manuscripts to
Go to Editorial Managerthetic socket, is due to its fiber strength and hardness, and low cost, but there are other more important things which must be considered than these specifications which are1the health1and safety. In this research fiberglass is replaced with monofilament fiber in order to be safe to on makers and users of this socket. In this paper two models of lamination manufacturing have been made and compared in terms of mechanical properties and fatigue life. The first is available and consists of: (4 perlon, 2 fiberglass and 4 perlon), The second is proposed lamination which consists of: (4 perlon, 1 cotton, 1 monofilament and 4 perlon). Simulations were conducted on the made socket made of two types of lamination by using ANSYS 14.5 to show the distribution of stresses, the amount of deformation and less safety factor for both cases. The results show an increase of 42% in the Young's modulus and a decrease in tensile stress and yield stress by 10.8% and 46% respectivel, As for the stress endurance it witnessed an increase of 140%.The simulation results show a decrease in the deformation by 40.7% and an increase in the minimum value of the safety factor of 0.323 to 1.05.
The effect of defect on structures and machines has negative consequences on them and it always takes researchers concern and attention in order to find feasible solutions to trace and detect the location of the defect accurately.In this research, the effect of a hole with different diameters on a square composite plate is studied as well as the effects of both the boundary condition and the plate thickness, furthermore, Vibration analysis of composite plate has been studied numerically and experimentally. The Numerical analysis has been carried out by using FEM by building MATLAB program as well as (ANSYS 15). The experimental part of this research is done by using vibration measuring instruments. The rate of error among the experimental tests and the numerical solution is less than 15%. These results have been used an inputs to the Genetic Algorithm model that the defect is located by, with a high percentage of success.
The aim of this work is to optimize EPD variables (voltage, time, and focus) using alternating current through the Taguchi Design of Experiment (DOE). Coating Nano hydroxyapatite (Nano-HA) on a Ti6Al4V substrate depends on thickness and roughness, then characterization of a coating layer to determine the optimum state. Hydroxyapatite (HAp) powder was deposited on a Ti-6Al-4V alloy substrate by electro-deposition with ethanol as a solvent under AC current, to improve the alloy surface quality based on coating thickness and maximum coating mass meeting the requirements of a biological orthopedics application. Ethanol was used as a solvent to precipitate ketazone and HAp on the base alloy. Taguchi's approach was used in order to determine the optimal conditions for EPD and subsequently to apply various criteria for depositing the biochemical coating. The surface and cross-section composition of the paint is described by characterization. Numerous tests and inspections; Zeta, XRD and SEM stability test, water contact angle and optical microscopes were used to describe the surface morphology of the HAp layer. The value of the optimum conditions for deposition of the HAp layer which is a simultaneous thickness and maximum coating mass, was predicted at a sedimentation voltage of 40 V, 2 min sedimentation time and 1 g / L for the concentration of the suspended solution at room temperature. The validity of the model resulting from the response surface methodology was assessed by comparing the expected results with the experimental results. In addition, close agreement was observed between the experimental results and the expected results. For the solution at room temperature, the results obtained with the highest value of the coating thickness of 41at the surface roughness of 0.94 and the contact angle of the alloy before coating is 67.489º reduced to. 38.132º after plating, which indicates an increase in the harmony of the metal implant and biocompatibility.
In this vast world after an earthquake lessons are learned; many strategies have been considered in order to achieve a proper seismic strength capacity.The aim of this paper is studying the seismic behavior of a typical reinforced concrete bridge pier in Iraq and implementing a proper technique of strengthening in order to fix any damage that had happened.Structure of a full scale three-dimensional finite element model was used in order to simulate a reinforced concrete pier via the computer software ABAQUS/CAE 2017 using concrete plasticity damage model (CDP).Under the action of Halabja earthquake, which was recorded at city of Halabja in Iraq on 12 November 2017, the behavior of model was traced, analyzed and the resulted damages were managed.The finite element analysis results indicated that the proposed configuration of carbon fiber reinforced polymers laminates substantially increases the lateral load strength and deformation capacity of the bridge pier