Vol. 24 No. 1 (2021) Cover Image
Vol. 24 No. 1 (2021)

Published: July 31, 2021

Pages: 16-25

Articles

Study the Effect of Inductor and Pole Geometry on the Surface Roughness and Material Removal Weight Using Magnetic Abrasive Finishing Method

Basma Luay Mahdi 1 Ali H. Kadhum 2
1 Al-Khawarizmi College of Engineering, University of Baghdad
2 Automated Manufacturing Engineering Dept., Al-Khawarizmi College of Engineering, University of Baghdad
History
  • Received: July 18, 2020
  • Revised: December 3, 2020
  • Accepted: January 23, 2021
  • Available Online: July 7, 2021
DOI

https://doi.org/10.29194/NJES.24010016

Abstract

The traditional finishing method cannot keep up with recent labor market requirements, solve the problem of increasing production, improve the surface roughness and accuracy of workpiece. While the unconventional magnetic abrasive finishing (MAF) method has shown as a promising technique that can be used to finish complicated surfaces. MAF finishes metals, alloy, ceramic, and other materials that are difficult to finish by other processes. In another word, MAF improves the quality of surfaces with low cost._x000D_ This paper focuses on optimize and study the effect of inductor and pole geometry (radius of hole, angle of core, angle of pole, radius of pole), on (surface roughness (Ra) and material removal weight (W)) and fined the optimum values that increase the efficiency of MAF method. Taguchi method employed to study the influence of geometry parameters and find the optimum values using orthogonal array L9. The results conclude that the most significant factor that effects change in surface roughness (?Ra) and material removal weight(?W) are radius of the hole (R) and angle of core (?), respectively.

Keywords

References

  1. V. Jain, Advanced machining processes. 2009.
  2. D. Hayes and D. Wolford, “Art of reducing magnetostrictive effects in magnetic materials,” Pat. Trademark
  3. Off., no. U.S. Patent No 2,234,968, 1941.
  4. R. K. Jain and V. K. Jain, “Abrasive Fine Finishing Processes,” J. Manuf. Sci. Prod., vol. 2, no. 1, pp. 55–68, 2011.
  5. A. a Moosa, “Utilizing a Magnetic Abrasive Finishing Technique ( MAF ) Via Adaptive Nero Fuzzy ( ANFIS ),” Am. J. Mater. Eng. Technol., vol. 1, no. 3, pp. 49–53, 2013.
  6. M. G. Patil, K. Chandra, and P. S. Misra, “Magnetic abrasive finishing - A review,” Adv. Mater. Res., vol. 418–420, pp. 1577–1581, 2012.
  7. L. D. Yang, C. T. Lin, and H. M. Chow, “Optimization in MAF operations using Taguchi parameter design for AISI304 stainless steel,” Int. J. Adv. Manuf. Technol., vol. 42, no. 5–6, pp. 595–605, May 2009.
  8. B. Deepak, R. Walia, N. S.-I. J. S. E. M. Technol, and U. 2012, “Effect of rotational motion on the flat work piece magnetic abrasive finishing,” vol. 2, pp. 50–54, 2012.
  9. H. Yamaguchi, A. Srivastava, … M. T.-C. J. of, and U. 2014, “Magnetic Abrasive Finishing of cutting tools for high-speed machining of titanium alloys,” Elsevier, vol. 7, no. 4, pp. 299–304, 2014.
  10. S. M. Mousa, “Optimization the Parameters of Magnetic Abrasive Process Using Taguchi Method to Improve the Surface Roughness,” Al-Khwarizmi Eng. J., vol. 13, no. 2, pp. 11–19, 2017.
  11. A. Chaurasia and V. Wankhede, “Magnetic Abrasive Finishing of Inconel 718 Super Alloy Using Permanent Magnet Ankur,” Int. Res. J. Eng. Technol., vol. 05, no. 05, pp. 1165–1168, 2018.
  12. Y. Tian, C. Shi, Z. Fan, and Q. Zhou, “Experimental investigations on magnetic abrasive finishing of Ti-6Al-4V using a multiple pole-tip finishing tool,” Int. J. Adv. Manuf. Technol., vol. 106, no. 7–8, pp. 3071–3080, 2020.
  13. P. Munyensanga, P. Paryanto, and M. N. A. Aziz, “Application of Polishing AISI 316L Stainless Steel Ball Bearing with A Magnetic Abrasive Finishing Process: A Review,” Rotasi, vol. 20, no. 4, p. 249, 2019.
  14. P. Singh, L. Singh, and A. Kaushik, “Parametric optimization of magnetic abrasive finishing using adhesive magnetic abrasive particles,” Int. J. Surf. Eng. Interdiscip. Mater. Sci., vol. 7, no. 2, pp. 34–47, 2019.
  15. Y. M. Baron, S. L. Ko, and J. I. Park, “Characterization of the magnetic abrasive finishing method and its application to deburring,” Key Eng. Mater., vol. 291–292, pp. 291–296, 2005.
  16. F. F. Mustafa, A. H. Kadhym, and H. H. Yahya, “Tool geometries optimization for friction stir welding of AA6061-T6 aluminum alloy T-joint using taguchi method to improve the mechanical behavior,” J. Manuf. Sci. Eng. Trans. ASME, vol. 137, no. 3, pp. 1–8, 2015.
  17. D. K. Singh, V. K. Jain, and V. Raghuram, “Parametric study of magnetic abrasive finishing process,” J. Mater. Process. Technol., vol. 149, no. 1–3, pp. 22–29, 2004.